Bedienungsanleitung Argo FC - FCIBS9DC (Seite 6 von 16) (Englisch)

665472

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

AUTOMATIC OPERATION

DEFROSTING OF OUTDOOR UNIT HEAT

EXCHANGER

When the outdoor temperature is low, frost or ice may

appear on the heat exchanger coil, reducing the heating

performance. When this happens, a protection function

for the heat exchanger defrosting is activated. During this

function operation, the fan of the indoor unit stops. Heating

operation restarts after several minutes. (This interval

will vary slightly depending on the room and outdoor

temperature).

HEATING PERFORMANCE

A heat pump conditioner heats a room by taking heat

from outside air. The heating efficiency will fall off when

the outdoor temperature is very low. If enough heat is not

obtained with this air conditioner, use another heating

appliance in conjunction with it.

Example of operation diagram in the (Auto) mode

with the set room temperature at 23°C.

NOTE

The air conditioner changes the operation mode (from cool

to heat or vice versa, if one of the following conditions

occurs:

- ZONE A: changes if the difference between the room

temperature and the temperature set on the remote

control unit is at least 3°C..

- ZONE B: changes if the difference between the room

temperature and the temperature set on the remote

control unit is at least 1°C, one hour after the compressor

stop.

- ZONE C: never changes if the difference between the

room temperature and the temperature set on the remote

control unit is no more than 1°C.

1. Set the or selector to AUTO (symbol on the

display; also the symbol or remains displayed).

2. Press the

+/- buttons (temperature selection)

to set the

desired temperature (the temperature range is between

32 °C max. and 10 °C min.).

When this setting is selected, the air conditioner will operate

automatically switching to the COOL or HEAT mode as

appropriate (regardless of the symbol displayed).

THE DISPLAY SHOWS THE

SELECTED TEMPERATURE.

AFTER 5 SECONDS FROM THE

REQUIRED TEMPERATURE SETTING

THE DISPLAY WILL SHOW THE ROOM

TEMPERATURE AGAIN.

3. Press the FAN selector button to the setting you want.

During Automatic Operation (+ IFEEL ON) the set

temperature is understood as perceived one, then the

system is automatically adjusted not only according to the

air temperature, but also based on the relative humidity,

according to the “humidex” index.

Verify that the unit is connected to the

main power and the STANDBY lamp is

light up.

1. Set the selector to COOL (symbol

on the display).

2. Press the +/- buttons (temperature

selection) to set the desired temperature

(the temperature range is between 32 °C

max. and 10 °C min.).

HOW TO SET THE PRESENT TIME

HEATING

1. Press the button ST three times.

The time indication alone flashes.

2. Press the H button until the present time hour is

displayed. Press the M button until the present time

minutes are displayed. The display will automatically

stop flashing.

1. Set the selector to HEAT (fixed or blinking symbol

on the display.

2. Press the +/- buttons (temperature selection) to set

the desired temperature (the temperature range is between

32 °C max. and 10 °C min.).

THE DISPLAY SHOWS THE

SELECTED TEMPERATURE.

AFTER 5 SECONDS FROM THE

REQUIRED TEMPERATURE SETTING

THE DISPLAY WILL SHOW THE ROOM

TEMPERATURE AGAIN.

3. Press the FAN button to select the fan speed.

For several minutes after the start of heating operation, the

indoor fan will stop until the indoor heat exchanger coil has

warmed up sufficiently. This is because the COLD DRAFT

PREVENTION SYSTEM is operating. During this period,

the STANDBY lamp remains lit.

NOTES

COOLING

THE DISPLAY SHOWS THE

SELECTED TEMPERATURE.

AFTER 5 SECONDS FROM THE

REQUIRED TEMPERATURE SETTING

THE DISPLAY WILL SHOW THE ROOM

TEMPERATURE AGAIN.

3. Press the FAN button to select the fan speed.

NOTE

Generally the fan stops when the set temperature is

exceeded (when you have selected the fixed HEATING

symbol ).

HEATING RECIRCULATION FUNCTION

If you want to let the fan run even after the set temperature is

exceeded, for example, in order to make the heating, coming

from a nearby source, circulate (eg. fireplace installed under

the air conditioner), press the selector until the blinking

HEATING symbol is displayed.

ONON ON

∆ 1 H ∆ 1 H

MIN.MAX.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo FC - FCIBS9DC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo FC - FCIBS9DC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info