Bedienungsanleitung Argo IRO Plus (Seite 14 von 17) (Englisch)

724572

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

V 11/19

(3) SLEEP BUTTON (on both the remote control and portable unit)

Press this button to reduce to minimum the ventilation, for the most silence.

Note: The sleep mode cannot be started in ventilation mode.

(4) FAN SPEED ADJUSTMENT BUTTON

Press this button when the appliance is switched on for adjusting the ventilation speed in cooling mode (AUTO), to low

(Low), medium (Med) or high (High).

The fan speed cannot be adjusted in DRY mode and is fixed to low speed.

(5) TIMER BUTTON (on both the remote control and portable unit)

Press and hold this button for 1 second to set the timer.

1）Timer-on (automatic switch-on)

When the appliance is off, this button is used to set a delay after which the unit will switch on.

Remote control: press “TIMER” to set a time to turn on the air conditioner. Press +/- to set the time, and press

“TIMER” again to confirm it. The “G” icon will remain on to indicate that the TIMER has been set.

Portable unit: Press TIMER. Press Timer again to select a number of hours from 1 to 24. Press the TIMER button

to confirm.

2）Timer-off (automatic switch-off)

When the appliance is running in the COOL mode, set a delay after which the unit will switch off.

Remote control: press “TIMER” to set a time to turn on the air conditioner. Press +/- to set the time, and press

“TIMER” again to confirm it.. The “G” icon will remain lit to indicate that the switch-off TIMER is running.

Portable unit: Press TIMER. Press Timer again to select a number of hours from 1 to 24. Press the TIMER button

to confirm.

Resetting the timer: If a TIMER has been set, press TIMER to display the delay. Press TIMER again to cancel the

setting.

(6) “SWING” BUTTON

Press “SWING” top turn on or off the swing function.

(7) TEMPERATURE + - AND TIMER ADJUSTMENT BUTTONS

The temperature can be adjusted to between 16 °C and 30 °C.

Increase temperature（+):

1) Allows for adjusting the desired temperature in cooling (COOL) mode.

2）Whenever the（

+) button is pressed, the set temperature increases by 1 °C.

Decrease temperature (

- ):

1) Allows for adjusting the desired temperature in cooling (COOL) mode.

2）Whenever the (

- ) button is pressed, the set temperature decreases by 1 °C.

The same button allows for setting the TIMER.

(9) TANK OVERFLOW INDICATOR

If the tank is full this led will turn on.

(8) TEMPERATURE AND ERROR DISPLAY

In the event of a malfunction, the LED display shows an error code, which facilitates the solution of the problem. With

the exception of the FL message, full tank, when an error occurs do not attempt to repair the air conditioner, always

take it to an Argoclima Service Center.

Problem Cause Solution

FL Tank full of water. Empty the tank.

If the problem persists, contact a service centre.

E1 Room temperature sensor failure. Contact a service centre.

E2 Failure of temperature sensor on the

evaporator.

Contact a service centre.

Il display temperatura ed errori si accende solo nelle modalità COOL. Nelle modalità DRY e FAN non si accende

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo IRO Plus Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo IRO Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info