Bedienungsanleitung Argo Zelos (Seite 12 von 13) (Englisch)

724685

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

V 01/20

(5) SPEED BUTTON

In the cooling and fan modes, press this button to adjust the ventilation speed to low (Low) or high (High). In certain

conditions, the fan speed may not function according to the settings.

In dehumidifying mode, this button cannot be pressed, thus the fan will forcefully choose the low fan speed.

(6) TIMER BUTTON

a. When the air conditioner is off, press “TIMER” to set when to switch the unit on. Press “+” o “–“ to set the time.

b. When the air conditioner is on, press “TIMER” to set when to switch the unit off. Press “+” o “–“ to set the time.

TROUBLESHOOTING

Troubles Possible Causes Su

ested Remedies

Unit does not start when pressing

power button

- Water full indicator lamp blinks, and water tank

is full. (W.F.)

Dump the water out of the

water tank.

- Room temperature is lower than the setting

temperature.

Reset the temperature

Not cool enough - There are heat sources inside the room. Remove the heat sources if

possible

- The doors and windows are not closed Make sure all the doors and

windows are closed

- Exhaust air hose is not connected or blocked. Connect or clean the

exhaust air hose.

- Temperature setting is too high. Reset the temperature

- Air inlet is blocked. Clean the air inlet.

Noisy

- The ground is not levelled or not flat enough Place the unit on a flat, level

ground if possible

- The sound comes from the flowing of the

refrigerant inside the air conditione

It is normal.

E2 Code - Water tank full in cooling mode Take off the rubber stopper

and empty the water tank.

CARE AND MAINTENANCE

WARNING!

Prior to carrying out any cleaning or maintenance, unplug the unit from the power socket.

1. Cleaning the air filters

The air filter must be checked at least once every two weeks of operation. Operating with dirty or clogged filters will

decrease the effectiveness of the air conditioner and can cause serious problems.

To remove the filter, release the rear grille then slide out the filter by gently pulling it sideways.

Use a vacuum cleaner to remove any dust. Should this not

be sufficient, wash the filter with lukewarm water (40°) and

neutral detergent (if necessary), rinse it with cold water

then leave it to dry naturally before putting it back in place.

After putting the filter back in place, close the grille and

resume use of the air conditioner.

2. Cleaning the casing.

Use a soft damp cloth to clean the outer surface of the air conditioner.

Do not use excessively hot water, solvents, petrol or other aggressive chemical

compounds, talcum powder and brushes: they may damage the surface or colour of

the casing.

Remove any stains using warm water with a little neutral detergent.

Do not pour water onto the air conditioner to clean it: this may damage the internal

components or cause a short circuit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argo Zelos Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Argo Zelos

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info