Bedienungsanleitung Argon SUB840 (Seite 3 von 7) (Englisch)

642255

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

w w w . a r g o n a u d i o . c o m 3

SUB840

speakers or away from the center of the stereo speakers.

This may have an impact on how you perceive the stereo

image, even though its only low frequency sounds that

come from the Subwoofer.

Trust your ears and be willing to experiment freely.

(Almost) everything is possible ☺

Running-in period

We recommend a running-in time of your new SUB840

Subwoofer of approximately 15-20 hours at normal listening

level before you decide on the final positioning and control

settings of the Subwoofer. During the running-in time the

drive units will settle in and perform as intended.

Connecting your Subwoofer

We recommend that you read the manual of your Amplifier

or AV-receiver carefully before connecting your Subwoofer.

First switch off the Amplifier and all equipment before you

connect the Subwoofer.

If your Amplifier/av-reciever has a SUB-OUT or PRE-OUT

function: Connect the Subwoofer input IN (10) as shown on

page 5 and your Amplifiers/av-recievers SUB-OUT or PRE-

OUT with a RCA/phono cable.

If your Amplifier does NOT have a SUB-OUT or PRE-OUT

function:

Connect the speaker cables from the Amplifier to the

Subwoofer (8) left/right, +/- as shown on page 5. Then

connect the satellite speakers to the Subwoofer using (7)

left/right, +/- as shown on page 5.

When finished connect the subwoofer net cable (6) as

shown on page 5 to the mains voltage, and push the

POWER ON/OFF button (4) as shown on page 5 to ON

position, the indicator lamp POWER LED will now glow blue

and the Subwoofer is active and ready to be used.

The Argon SUB840 Subwoofer has a built-in AUTO

STANDBY function and after approximately 10 minutes

without any input signal the subwoofer will automatically

switch off, and the indicator lamp POWER LED will change

color. When an input signal is detected the subwoofer will

become active and the indicator lamp POWER LED will

glow blue.

Setting volume, frequency and phase

The volume, crossover and phase (controls 1, 2 and 3 on

page 4-5 ) can be adjusted on the rear panel, and we

recommend that you adjust the setting of these controls to

your liking – try with different music and films. If you want

more detailed information on these control functions, we

invite you to visit our homepage www.argonaudio.com.

Care and cleaning

We don’t recommend use of any solvents or cleaners on

Argon SUB840 cabinet, the cabinet surface usually only

requires dusting or cleaning with a damp soft cloth

(only use cold clean water).

The grille fabric may be cleaned with a normal clothes brush

or vacuumed carefully with the grille detached from the

cabinet. Avoid touching the drive unit, and do not use the

Subwoofer as a coffee or drinks table (risk of water being

spilled into the subwoofer).

Disconnect the Subwoofer from the mains supply if taken

out of use for a longer period.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Argon SUB840 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info