642231

Argon TT1v2 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite


www.argonaudio.com 2
TT1
v
2
Connection to the amplifier
The external phono leads must be connected to your
amplifier.
Connections : Red right channel / Black left channel. If
your amplifier does not have an integrated phono stage
you will need to require an external phone stage. Ask at
your local hi-fi dealer..
Plug and play - Quick set up (factory fitted cartridge
only)
Your turntable has been designed to be very simple to
set-up and use. We have designed this turntable so that
correct tracking weight can be achieved by simply
pushing the balance weight as close to the stop point
as possible. Fig 2. This will automatically set the arm to
within the recommended tracking range for the factory
fitted stylus (1.5g - 2.0g). The Bias slider should be set
to the same figure as the tracking weight. Fig 3.
Advanced Set-up (when using a different model of
cartridge)
If you choose to change the factory fitted cartridge a
tracking pressure gauge is required to correctly apply
the required down force. Any Hi-Fi dealer should be
happy to help with this setup procedure when you
purchase a new cartridge. Always use a down force
which corresponds to the upper limit of the cartridge
maker's recommended range. A new cartridge must be
aligned correctly as shown in fig 4. Adjust the cartridge
position in the head-shell so that the stylus tip is
vertically aligned with the front of the hole marked A.
Ensure the cartridge is sitting square in the head-shell
before fully tightening.(Take care not to over tighten.
Set the bias adjustment slider fig 3. to the same number
as the tracking force. For example 1.5g tracking force =
1.5 on the bias slider.
Hints & Tips
Mount the turntable on a rigid, level surface. Avoid
mounting on hollow or heavy cabinets or anything
mounted on a flexible wooden floor. The Argon
turntable support is the ideal solution.
Keeping the lid closed while playing records will prevent
dust falling on to the record surface and should make
cleaning unnecessary. Depending on the room
environment and ambient temperature, playing with the
lid open may offer sonic improvements. You can
experiment to optimise the performance best suited to
your room.
Do not use any record cleaner that works while the
record is playing or any cleaners that use water or
solvents. If you keep your records stored in their
sleeves, avoid touching the playing surfaces and keep
all water and fluids away, cleaning should not be
necessary. Do not worry about visible dust on the
record surface, this is brushed aside by the stylus and
any that collects on the stylus can be easily blown
away. In general, record cleaning is overdone and one
should not believe all the claims made by record
cleaner manufacturers.
Leave the turntable running during a record playing
session. Switch on before the session and only switch
off after you have finished. This will increase the life of
the motor and drive belt.
Do not lift the centre hub out from the main bearing.
The bearing is factory assembled with a film of special
thick lubricant. If the centre hub is removed this film
may be disturbed and the accuracy of the turntable
could be affected.
The arm earth (or ground) is automatically connected
through the arm cable screening. No other earthing
should be necessary.
Save the original packing in case you ever need to
transport the turntable.
Do not use any polish on the turntable or lid. To clean,
wipe gently with a soft cotton duster (slightly damp only
if required).
Argon turntables are designed to optimise performance
for music reproduction and therefore no compromises
have been made to give quick start times. The normal
time taken for full speed to be reached is between 2
and 5 seconds.
Warning: Any attempt to repair or modify this turntable
by persons other than authorized personnel may
invalidate the guarantee. Should you experience any
problem with your turntable please contact your dealer.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Argon TT1v2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info