Bedienungsanleitung Ariston AW 125 (Seite 20 von 23) (Englisch)

543353

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

www.aristonappliances.us

Troubleshooting

Possible causes / Solutions:

 The plug has not been inserted into the electrical socket, or it has

not been inserted far enough to make contact.

 There is no power in the house.

 The porthole door has not been shut properly.

 The START/RESET button has not been pressed.

 The water tap has not been turned on.

 The water inlet hose is not connected to the tap.

 The hose is kinked.

 The water tap has not been turned on.

 There is no water in the house.

 The water pressure is insufficient.

 The START/RESET button has not been pressed.

 The end of the outlet hose has not been fitted at a height between

25 - 34 inches (62 and 86 cm) from the floor (see Installation).

 The free end of the hose is underwater (see Installation).

 If If the dwelling is on one of the upper floors of a building, there

may be problems relating to water drainage, causing the washing

machine to load and drain water continuously. Special anti-

draining valves are available in shops and help to avoid this

inconvenience.

 The water drainage system is not fitted with a breather pipe.

 The programme does not include a draining phase: some

programs require manual draining (see Programs and options).

 The Easy Iron option is enabled: to complete the program, press

the START/RESET button (see Programs and options).

 The outlet hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked properly when the appliance was

installed. Remove shipping bolts (see Installation).

 The washing machine is not level (see Installation).

 The washing machine is trapped between cabinets and a wall

(see Installation).

 The load is not balanced properly (see Operating the washing

machine).

 The water inlet hose is not screwed on to the tap correctly (see

Installation).

 The detergent dispenser drawer is blocked (for instructions on

how to clean it, see Care and maintenance).

 The outlet hose has not been secured properly (see

Installation).

 Switch off the machine and unplug the appliance; wait for

approximately 1 minute then switch it on again.

If the problem persists, contact the Assistance.

Malfunction:

The washing machine will not switch on.

The wash cycle does not begin.

The washing machines fails to fill with

water.

The machine continuously fills and

drains water.

The machine does not drain or spin.

The washing machine vibrates too much

during the spin cycle.

The washing machine leaks.

The icons corresponding to the Phase in

progress flash rapidly at the same time

as the ON/OFF indicator light.

From time to time your machine may not operate as it should. Before calling for Assistance (see Service-Assistance),

make sure that the problem cannot be resolved easily using the following list.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston AW 125 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info