Bedienungsanleitung Ariston LI620 (Seite 8 von 11) (Englisch)

48074

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

If the power

socket to which

the appliance is

connected is not

compatible with

the plug, replace

it with a suitable

plug rather than

using adapters or

multiple plugs as

these could cause

overheating or

burns.

Installation and moving

After having bought or moved your dishwasher to another home, a

correct installation ensures that your dishwasher will operate

smoothly and efficiently.

tightly onto the tap (see fig. 2).

If the water pipes are new or have

not been used for an extended

period of time, let the water run to

make sure that the water is clear

and free of impurities. If this

precaution is not taken, there is a

risk that the water inlet can get

blocked and damage the appliance.

Hot water connection.

Your dishwasher can be supplied

with hot water from the mains

supply (if you have a central heating

system with radiators) at a tempe-

rature of no more than 60°C.

In this case, the wash cycle time

will be about 15 minutes shorter

and the wash will be slightly less

effective.

The connection must be made to

hot water supply following the

same procedures as those indicated

for the cold water connection.

Drain hose connection.

Fit the drain pipe into a drain line

with a minimum diameter of 4 cm

or place it over the sink. Avoid

restricting or bending it. Use the

special plastic elbow provided (see

figure) to position it in the best

possible way. The part of the pipe

marked with the letter A should be

between 40 and 100 cm above the

ground.

The pipe should not be immersed

in water.

Electrical connection.

First of all, check that the mains

voltage and frequency values

correspond to those stated on the

rating plate located on the stainless

steel inner door of the appliance

and that the electrical system to

which the dishwasher is connected

is sized for the maximum current

indicated on said rating plate.

Earth: indispensable

safety.

Only now can you plug the

appliance into a socket provided

with an efficient earth connection

(the system's earthing is a

guarantee of safety provided for by

law, make sure your system has

it).

Power supply wire.

Check the power supply wire on a

regular basis; if it is damaged, we

recommend you have it replaced

by an authorised technical

Assistance service centre.

Choose where you want to install

your dishwasher, you can even

place it so that its sides or back

panel are side by side with furniture

or up against the wall. The

dishwasher is provided with water

supply and drain hoses, which can

be directed towards the left or right

to facilitate appropriate

installation.

Levelling.

Once the appliance is positioned,

adjust the feet by screwing them in

or out depending on how high you

want it and to level it so that it is

horizontal. Make sure that it is not

inclined more than 2 degrees. If the

appliance is level, it will help ensure

its correct operation.

Adjusting the back Feet

Insert the appliance into the cutout

and then adjust the height using the

screws located on the front bottom

part of the machine. Use a

screwdriver to turn the screws in

the clockwise or anti-clockwise

direction to increase or decrease

the height respectively.

Cold water connection.

This electric household appliance

should be connected to the water

mains using the cold water supply

hose provided with the appliance

only. Do not use a different hose. In

the event of replacements, use

original spare parts only.

Connect the cold water supply

hose to a 3/4 gas threaded connec-

tion, placing the small filter

provided between the hose and

connection, taking care to screw it

Your dishwasher has arrived

The special

plastic elbow

should be

fastened firmly

onto the wall to

prevent the drain

hose from

moving and

allowing water to

spill outside the

drain.

Fig.2

Condensation-proof tape.

On some models, a transparent

condensation-proof adhesive tape

has been provided.

It should be stuck onto the lower

side of your wooden worktop to

protect it from the formation of

condensation.

When not provided, this tape can

be requested as a spare part from

authorised retailers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ariston LI620 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info