Bedienungsanleitung Aritech AD111 (Seite 2 von 6) (Englisch, Holländisch, Französisch, Italienisch)

702269

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Installation Instructions

INTRODUCTION

The AD111 is an internal interface for an addressable

detector system. It connects a generic detector with dry

alarm and tamper contacts to the Advisor MASTER

ATS1290 Point-ID DGP. The interface is equipped with two

inputs for connecting the alarm relay and the tamper switch

of the detector, and an open collector output. This output

can be used for example; to enable/disable the alarm LED

on the detector (depending on the detector’s other

functionalities, which can be programmed).

DEVICE CATEGORY

The AD111 is of the device category I/O, type 2 and will be

automatically recognised after learning the device into the

ATS1290 DGP. For more details about device categories

and types, please refer to the ATS1290 manual.

MOUNTING THE UNIT

The AD111 PCB (Fig. ) is mounted underneath the PCB

in the housing of the detector that is connected to the

Point-ID bus (Fig. o). Connect terminals 1 to 4 to the Point

ID bus and external power supply.

CAUTION! Before mounting the AD111 Internal

PID interface in a (existing) PIR detector,

disconnect the mains power before opening the

panel, DGP or external power supply cabinet.

1. Open the detector.

2. Remove the PCB from the detector.

3. Connect the flying leads 5 - 11 to the existing detector

connections (see fig.

,  and q).

Number Colour AD111 PIR

5 Black 0V from AD111 0V to PIR

6 Red +12V from AD111 +12V to PIR

7 Blue Alarm input Alarm output

8 Blue Alarm input Alarm output

9 Yellow Tamper input Tamper output

10 Yellow Tamper input Tamper output

11 White Walk test output Walk test input

4. Connect the Point ID bus and auxiliary power supply to

terminals 1 - 4 (see Fig. q.)

Important:

The Point ID bus in – (ground) must be coupled to the

external power supply in – (ground) to ensure correct

operation! Connect the bus and detector grounds in the

control panel or close to the detector where the auxiliary

power supply is located.

TOPOLOGY AND DETECTORS

Please refer to the ATS1290 manual.

CABLE SPECIFICATION

Please refer to the ATS1290 manual.

ADDRESS SETTING AND ZONE NUMBERING

Set the AD111 Internal PID Interface to its unique address

on the Point ID bus. For details, see figure

.

The address setting of the AD111 will immediately

correspond with zone number and output in the range of

the ATS1290 DGP

Refer also to the ATS1290 manual for the direct link to the

zone number (control panel).

For convenience the output also can be configured to

connect to any output in the DGP range (for more details

see the explanation at the end of the memory location

map).

THE ATS OUTPUT

The walk test can be programmed through the control

panel by activating an output in the DGP range.

MEMORY LOCATION MAP

Every PID device has its own characteristics concerning

related I/O lines or certain functionality of the device.

A total of 16 memory locations are reserved to configure

the PID devices. Only the first nine normally are user

configurable. This depends on the functionality of the

particular device.

For the AD111 internal PID interface only memory location

6 matters.

On memory location 6 the ATS-style output can be

configured.

*ATS-style output

The output can be used to enable/disable the Alarm LED or

Walk Test LED on the detector. ATS output and zone

numbering are equivalent.

The default output number of the device equals the input

number when memory location 6 is set to 0 (default).

Please refer to the PID DGP manual for PID address

settings and zone numbering.

The output number on the AD111 can also be changed

within the DGP output range (e.g. DGP 1 output 17-32). If

the output of this device or all the outputs of similar devices

on the same DGP need to be programmed on for example

output 32, simply program memory location 6 of all those

I/O devices to 32.

TECHNICAL SPECIFICATIONS

Bus protocol ..................................... GE Interlogix Point ID

Bus voltage ..............................................12 V or 24 V

External power supply..............................9 V – 13.8 V

Current consumption from bus...................... 330 µA ±10%

Unit load for DGP..............................................................1

Address range........................................................0 to 255

Current O/C output...........................................100µA max.

Category.........................................................................I/O

Device type .....................................................................T2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech AD111 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info