675140
4
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
4
Temperature setting
MICROLINE has a temperature setting range of 0-40°C.
To help set the temperature correctly, the thermostat has an LED,
which lights red when heating is activated. Set the thermostat to max.
temperature until the required room or floor temperature is reached.
Then reduce the temperature setting until the LED goes out. If
necessary, fine adjustment can be performed after 1 or 2 days.
Night setback
The night setback/economy temperature function is activated via a
230 V signal from an external timer connected to terminal S.
The function is factory set to 5°C (2-8° OTD2). The LED lights green
when the economy signal is active and red when heating is active.
Frost protection
If the signal is connected via a rectifier diode, the thermostat will
maintain a floor/room temperature of 5°C.
Pollution class: 2
Pollution class 2, representative of air circulation in typical homes.
Overvoltage category: III
Pulse voltage 4 kV to IEC 60664-1.
Sensor installation
Floor sensor:
The floor sensor should be installed in standard conduit embedded in
the floor. The conduit should be sealed and positioned as close to the
floor surface as possible.
Room sensor:
The room sensor should be installed in a standard wall box or
mounted direct on the wall. Sensor cables can be extended up to a
maximum of 50 m in length using power cable. Two wires in a multi-
wire cable must, however, not be used if the cable is also used to
supply power to heating cables. The best result is achieved if a
separate cable, installed in a separate conduit, is used for the sensor.
Installation of thermostat with built-in or external room sensor
The thermostat or external room sensor should be mounted on a wall
in such a way as to allow free air circulation around it. It must also be
positioned so as to prevent it from being affected by direct heat
sources (e.g. the sun), draughts from doors and windows, or outside
temperature (i.e. do not mount on outer walls). MICROLINE has a
built in fault circuit which switches the heating off if the sensor is
disconnected or short-circuited.
Thermostat installation
- Open cover.
- Unscrew cover and remove.
- Connect wires from rear as shown in wiring diagram.
- Mount thermostat in wall box - fit frame and cover.
English
Increase temperature
LED
Interrupter
Programming button (P)
Decrease temperature
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Arnold Rak OTN 2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info