309039
33
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
Page 15
ENGLISH
ENGLISH
Height 33-1/2”–34-1/2 (850–876 mm)
Width 23-7/16” (595 mm)
Depth W640/W660: 23-7/16" (595 mm)
W600/W620: 24-7/16” (620 mm)
Weight 167 lbs. (73 kg)
Rated load See data plate
Supply voltage Single-phase 230 V, 60 Hz
Heating element 2000 W
Fuse 15 A
ACCESSORIESACCESSORIES
WAWATER SUPPLTER SUPPLY CONNECTIONY CONNECTION
Because ASKO washers have their own heating
element, you only need to have a cold water inlet. The
connection should be made by someone who is
sufficiently skilled. Use the hose supplied with the
washer.
Water pressure must be in the range of 15–146 PSI.
A tap should be fitted on the water supply pipe.
If a new supply pipe has been installed for the washer,
it should be flushed thoroughly to remove any foreign
particles that might clog the strainer in the water inlet.
INSTINSTALLAALLATION INSTRTION INSTRUCTIONSUCTIONS
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
NOTE:
Cosmetic damage must be reported to your
dealer within five days from the date of
purchase. After unpacking the washer,
thoroughly check the unit for cosmetic damage.
SPECIFICASPECIFICATIONSTIONS
Drum and Barrel Stainless steel
Outer casing Stove-enamelled hot-dipped
galvanized steel
Mounting Four adjustable rubber-covered
feet
Inlet supply hose 5 ft. (1.5 m) PEX tubing with
brass ferrules
Supply pressure 15–142 PSI
Outlet hose 5.5 ft. (1.7 m) polypropylene hose,
3/4” ID
REMOREMOVING VING THE SHIPPINGTHE SHIPPING
SUPPORTSSUPPORTS
The machine is transported with three shipping
supports, as illustrated below. These supports hold
the tub in place during shipment. When you unpack the
machine, you must remove these supports.
1. Unscrew the 5/8” (13
mm) bolts holding
the supports in place
and remove the
bolts.
To remove these supports, follow the instructions
below:
You must remove the
shipping supports
before you install the
washer.
2. Push the rubber
spacer up then pull it
out of the slot.
ADJUSTING THE FEETADJUSTING THE FEET
It is important that the machine is level so it won’t vibrate
excessively during the spinning cycles. Each foot on
the washer is adjustable, so you can level the washer
on any surface. Once it is level, securely tighten the lock
nuts on the feet to prevent excessive vibration during
the spin cycles.
Be sure to tighten the
lock nuts securely
when you level the
machine.
Cold water
supply
Tap
4. Insert it into the slot
and push down to lock
it into position.
3. Rotate the spacer so that the extruded
end points toward the machine.
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Asko w 620 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Asko w 620

Asko w 620 Bedienungsanleitung - Englisch - 2 seiten

Asko w 620 Bedienungsanleitung - Englisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info