Bedienungsanleitung ATAG VA7016RT (Seite 4 von 24) (Englisch)

675534

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Before washing for the

first time

1. Checking water hardness

In order to achieve good dishwashing results, the dishwasher needs

soft water (water with low mineral content). Hard water leaves a white

coating on dishes and the dishwasher.

Water hardness is specified using the following scales: The German

water hardness scale (°dH) and the French water hardness scale (°fH).

A water supply with a water hardness in excess of 6°dH (9°fH) must

be softened. This is done automatically with the aid of the built-in water

softener. In order for the softener to function optimally, it must be

adjusted to the hardness of the water supply.

Contact the local waterworks, or measure the water hardness using

the supplied test strip, to check the water hardness in your area. Once

you have adjusted the water softener, use detergent and rinse aid

doses suitable for soft water.

How to use the test strip:

1 Turn on the water tap and let the water run for a minute or so.

2 Fill a glass with water.

3 Remove the test strip from its packaging.

4 Dip the test strip in the water for about one second.

5 Wait one minute. Now compare the colours of the squares with the

water hardness table.

°fH°dHTest strip

<5<3

4 green

>7>4

1 red

>15>8

2 red

>25>14

3 red

>38>21

4 red

2. Basic settings

To switch on the dishwasher, press and hold the main power switch

until the display lights up.

"This is a first time set up." is shown on the display. It is important

that you choose the right settings to ensure good dishwashing results.

Confirm setting

Select setting

Main power switch

Settings

Language1

Select the language to be shown on the display.

Rinse aid 0/1/2/3/4/5/TAB2

Drying is faster and a better result is achieved if you use rinse aid.

You will also achieve a better dishwashing result with clear and

spotless dishes.

Select rinse aid dosage. The rinse aid dispenser can be adjusted

between 0 (Off) and 5 (High dosage).

When using an all-in-one detergent that contains rinse aid, you can

activate the setting TAB. Read more about all-in-one detergent in the

chapter Using the dishwasher.

Pre-selected at factory: 5

Water hardness 0/1/2/3/4/5/6/7/8/93

Choose a setting depending on the hardness of the water supply.

See the water hardness table below. It is important that this setting

is correct!

°dH

0-5

6-8

9-11

12-14

15-19

20-24

25-29

30-39

40-49

50+

0-9

10-14

15-20

21-25

26-34

35-43

44-52

53-70

71-88

89+

°fH

°dH

°fH

Do not forget to put salt in the salt compartment after you have set

the water softener to 1 - 9.

For a water supply with a hardness under 6°dH (9°fH), select 0. The

water softener is deactivated and no salt is needed.

Pre-selected at factory: 4

To change the chosen setting, see the chapter Settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG VA7016RT Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG VA7016RT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info