Bedienungsanleitung ATAG VA7016SRT (Seite 21 von 24) (Englisch)

675536

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Installation

859*- 912

559

700-800**

193

442

573

596

131-186

30-94

1238

740

1294**

760-840**

105

[mm]

Nominal dimensions. Actual measurements may vary.

*Remove locking nuts for an installed height of 820-821 mm.

Cover door with slide function fitted, which means the cover door slides

upwards when the dishwasher is opened.

Door length

It is important that you read through and follow the instructions and

directions below. Conduct installation and connection in accordance

with the separate installation instructions.

Safety instructions

• Connections to electricity, water and drainage must be performed

by a qualified professional.

• Always follow applicable regulations for water, drainage and

electricity.

• Take care during installation! Wear protective gloves! There must

always be two people!

• Place a drip tray on the floor beneath the dishwasher to prevent

damage from any water leaks.

• Before screwing the dishwasher into place, test the dishwasher by

running the Rinse and hold programme. Check that the dishwasher

fills with water and drains. Check also that none of the connections

leak.

WARNING!

Turn off the water supply when installing the dishwasher!

The plug must be disconnected or power to the socket turned off

while the work is carried out!

Setup

• The recess and connection dimensions are included in the separate

installation instructions. Check that all dimensions are correct before

starting the installation. Note that the height of the cover door can

be adjusted to match other fittings.

• Make sure the area on which the dishwasher is to be installed is

firm. Adjust the adjustable feet so that the dishwasher is level.

Tighten the lock nuts.

• Affix the protective film (packed in the document bag) to the

underside of the worktop. The protective film is to protect the

worktop from moisture.

• Check that the machine is installed such that the door opens freely,

otherwise door lock functionality may be disrupted.

Drainage connection

See the separate installation instructions for necessary information.

This dishwasher is suitable for installing in a raised recess (to attain

an ergonomic working height). This means that the dishwasher can be

placed so that the drainage hose runs to a lower level than the bottom

of the dishwasher, such as by routing it directly to a floor drain. The

dishwasher is fitted with an integrated anti-siphon device to prevent

the machine from being emptied of water during the wash cycle.

The drainage hose can also be connected to a connection nipple on

the sink unit's water trap. The connection nipple must have an internal

diameter of at least 14 mm.

The drainage hose may be extended by a maximum of 2.5 m (the total

length of the drainage hose must not exceed 4.5 m). Any joins and

connecting pipes must have an internal diameter of at least 14 mm.

However, the drainage hose should ideally be replaced with a new

hose without joins.

No part of the drainage hose may be more than 950 mm above the

bottom of the dishwasher.

Ensure that the drainage hose has no kinks.

Connection to water supply

Use only the inlet hose supplied with the dishwasher. Do not re-use

old or other spare hoses.

The supply pipe must be fitted with a water tap (stopcock). The water

tap must be easily accessible, so that the water can be shut off if the

dishwasher has to be moved.

Once the installation is complete, turn on the water tap and allow the

pressure to settle for a while. Check that all connections are watertight.

Connection to cold water supply

Connect the dishwasher to the cold water supply if the building is

heated using oil, electricity or gas.

Connection to hot water supply

Connect the dishwasher to the hot water supply (max. 70 °C) if the

building is heated using an energy-efficient means such as district

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ATAG VA7016SRT Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von ATAG VA7016SRT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info