Bedienungsanleitung ATAG WV 6211 LM (Seite 14 von 16) (Deutsch, Englisch, Holländisch, Französisch)

121870

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

paperwork indicates that the appliance should not be treated

as domestic waste, but should be delivered to a suitable

electric and electronic appliance recycling collection point.

Follow local guidelines when disposing of waste. For more

information on the treatment, re-use and recycling of this

product, please contact your local authority, domestic waste

collection service or the shop where the appliance was

purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out

by specialised personnel.

• Electric Connection

The appliance has been manufactured as a class II, therefore

no earth cable is necessary.

The plug must be easily accessible after the installation of

the appliance.

• The minimum distance between the support surfaces of

the cooking pots on the cooker top and the lowest part of

the cooker hood must be at least 65 cm.

If a connection tube composed of two parts is used, the upper

part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conduc-

tor used to circulate hot air or for evacuating fumes from other

appliances generated by other than an electrical source.

The following procedures must be performed before the

appliance is installed:

- For easier handling of the appliance, remove the grease

 lter(s) (Fig. 2).

- If the product is a  lter model, remove the extractable  lters

by pulling lever H outwards as indicated in (Fig. 3).

- Fit the  ange to the air outlet hole by turning it until it clicks

into place, then  x it using a screw (Fig. 10).

In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

(*) Warning: plastic spacer  tting.

This product may also be supplied with a plastic spacer O, which

should be  tted before the hood is installed (Fig. 7).

Fix the spacer to the hood using screws P (Fig. 7).

To assemble the unit correctly, align the front panel of the

hood with the wall cabinet and decide on the distance

necessary to  ll in any space remaining between the hood

and the wall.

Once the distance has been established, use a cutter to remove

the excess plastic (Fig. 7).

This product may be installed in 2 di erent ways:

Type A installation,  gure 4

- Fixing the hood to the lower part of the wall cabinet

Type B installation,  gure 5

- Fixing the hood to the wall

- Fixing the hood to the lower part of the wall cabinet

(Fig. 4A)

1. Using the drill template supplied, make 2 holes (E) in the

sides of the wall cabinet, in line with hooks D (Fig. 4).

Position the hood inside, so that the internal side hooks D can

be positioned into the two holes E.

GENERAL

Carefully read the following important information regarding

installation safety and maintenance. Keep this information

booklet accessible for further consultations.

The appliance has been designed for use in the ducting ver-

sion (air exhaust to the outside),  ltering version (air circulation

on the inside ) or with external motor .

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneou-

sly with an open  replace or burner that depend on the air

in the environment and are supplied by other than electrical

energy, as the cooker hood removes the air from the environ-

ment which a burner or  replace need for combustion. The

negative pressure in the environment must not exceed 4Pa

(4x10

-5

bar). Provide adequate ventilation in the environment

for a safe operation of the cooker hood.

Follow the local laws applicable for external air evacuation.

Before connecting the model to the electricity network:

- control the data plate (positioned inside the appliance)

to ascertain that the voltage and power correspond to the

network and the socket is suitable. If in doubt ask a quali ed

electrician.

- If the power supply cable is damaged, it must be replaced

with another cable or a special assembly, which may be

obtained direct from the manufacturer or from the Technical

Assistance Centre.

2. WARNING !

In certain circumstances electrical appliances may be a

danger hazard.

A) Do not check the status of the  lters while the cooker

hood is operating

B) Do not touch bulbs or adjacent areas, during or straight

after prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker

hood

D) Avoid free  ame, as it is damaging for the  lters and

a  re hazard

E) Constantly check food frying to avoid that the overhe-

ated oil may become a  re hazard

F) Disconnect the electrical plug prior to any mainte-

nance.

G) This appliance is not intended for use by young children

or in rm persons without supervision

H) Young children should be supervised to ensure they do

not play with the appliance

I) There shall be adequate ventilation of the room when

the rangehood is used at the same time as appliances

burning gas or other fuels

L) There is a risk of  re if cleaning is not carried out in

accordance with the instructions

This appliance conforms to the European Directive EC/2002/96,

Waste Electrical and Electronic Equipment (WEEE). By making

sure that this appliance is disposed of in a suitable manner,

the user is helping to prevent potential damage to the

environment or to public health.

The

symbol on the product or on the accompanying

ENGLISH

- 14 -

ATAG WV 6211 LM Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info