Bedienungsanleitung Atika MHD 2800 W (Seite 14 von 132) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

519876

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

L Mains connection

 Compare the voltage given on the machine model plate e.g.

230 V with the mains voltage and connect the machine to the

relevant and properly earthed plug.

 Only use extension cables with sufficient core cross-section.

Mains fuse

Switzerland UK

2300 W 16 A time-lag

10 A time-lag

13 A time-lag

2500 W 16 A time-lag

13 A time-lag

2800 W 16 A time-lag

13 A time-lag

On / Off switch

Do not use any device where the switch can not be switched

on and off. Damaged switches must be repaired or replaced

immediately by the customer service.

Switch on

Press the green button I .

Switch off

Press the red button 0 .

Restart protection in case of power

failure

In case of a power failure, the device switches off automatically

(zero-voltage initiator). To restart, press the green button again.

Motor protection

The motor is equipped with a safety switch and switches off

automatically when overloaded. After a cooling-down break

(approx. 5 min), the motor may be restarted. Press the

1. reset button (motor protection)

2. green button I to restart.

Electrical mains supply impedance

When conditions in the electrical mains supply are un-favourable,

voltage reductions for short periods can occur during the process

of turning on the equipment, which can adversely affect other

equipment (e.g., the flickering of a lamp).

No breakdowns are to be expected if the maximum, electrical

mains supply impedances given in the table are met.

Power consumption P1 (W) Electrical mains supply

impedance Zmax (W)

2300 0,21

2500 0,21

2800 0,19

 Choose a working position alongside the equipment or be-

hind it. Never stand near the ejection opening.



Longer material that is protruding from the device could

spring back when it is drawn in by the blades! Observe safety

distance!

 Never reach into the filling or ejection opening.

 Keep your face and body away from the filling opening.

 Never place hands, other parts of the body or clothing into the

filler funnel, ejection channel or in the vicinity of other moving

parts.

 Check that no chopped residues are in the filling hopper be-

fore switching on the equipment.

 Do not tip or tilt the machine when the motor is running.

 When filling, be careful that no pieces of metal, stones, bottles

or other objects unintended for processing, enter the filling

hopper.

 Immediately switch off the equipment and allow it to come to a

stop, if foreign objects enter the filling hopper or if the equip-

ment starts to make unusual noises or vibrates. Remove the

mains plug and carry out the following checks:

− inspect for damage,

− replace or repair damaged parts,

− check the equipment and tighten loose parts.

You must not repair the equipment yourself if you are

unauthorized to do so.

 What can I shred?

Yes:

• organic household and garden waste

e. g. hedge and tree cuttings, dead flowers and vegetable

kitchen waste.

No:

• glass, metal, plastic, plastic bags, stones, cloth, roots with

soil, food left-overs, fish or meat.

OFF

Reset button

(motor protec-

tion)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika MHD 2800 W Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info