Bedienungsanleitung Audison srx 1 (Seite 2 von 2) (Englisch)

163435

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

ELECTRIC BASS AND ACOUSTIC BASS EXPLAINED

The SRx1 ampliﬁ er was created for maximum acoustic enhancement and enjoyment of

low range frequencies, allowing the best match between this ampliﬁ er and the chosen

subwoofer system.

For this reason, the SRx1 is designed with two groups of separate speaker outputs

labelled: Electric Bass and Acoustic Bass. Each group includes two pairs of terminals.

Because of the unique circuit topology of this ampliﬁ er, it is required that only a four-

ohm load be connected to each terminal for a total load of two-ohms. For example, if

you are using a dual four-ohm voice coil subwoofer, each coil should be connected

to a separate terminal. No matter what conﬁ guration of subwoofers you use, each

terminal must be connected to a four-ohm load or no load. Please see further wiring

conﬁ gurations in the owners manual.

WARNING: Do not use both Electric Bass and Acoustic Bass outputs at the same time.

You must choose only one output: Electric Bass or Acoustic Bass.

The two different modes are distinguished by the different characterization of the bass

timbre; however, this is not accomplished through ﬁ ltered equalization of the sound, but

through the variation of the ﬁ nal output stage characteristics.

Some electric parameters also vary, the most important being the damping factor,

which determines the ability of the ampliﬁ er to control the subwoofer.

The choice of which output group you should use, strongly depends on the listener’s

tastes and the subwoofer system being used.

If you use this ampliﬁ er to drive full range loudspeakers, for instance in a Dual Mono

conﬁ guration, you have a choice of the bass timbre according to the output terminals

you use.

Following is a technical description of the output choices.

ELECTRIC BASS Output: Damping Factor 300

A precise, deep and stable bass, without any speciﬁ c coloration, acoustically

characterizes this output. This setting is best for under damped loudspeaker/enclosure

systems (Q of 0.7 to 1), generally deﬁ nable as Reﬂ ex (vented) systems. On these

systems, it keeps better control of the woofer under high power applications.

ACOUSTIC BASS Output: Damping Factor 70

BIG bass, highlighting dynamic impact, acoustically characterizes this output. It is

especially suitable for techno, electronica and club music and is especially useable

for achieving high SPL scores. We suggest its use for over damped loudspeaker/

enclosure systems (Q of 0.5 to 0.7), generally deﬁ nable as Acoustic Suspension

(sealed) systems.

No one setting is correct for every listener. We suggest you try listening to your music

in both output modes and make your decision accordingly. Close your eyes, sit back,

listen and let your ears make the decision.

CONFIGURATION TABLE

SUBSONIC SUB EQUALIZER SUBWOOFER

MODE FREQ. MODE FREQ.LEVEL FREQ.

RESPONSE

CURVE

SUBW.

Freq.

SUBW.

EQ.

Freq.Freq.

SUBW.

EQ.

Freq.Freq.Freq.

SUBS.

Freq.

SUBS.

INPUTS SPEAKERS OUT mono

Pre In (L; R; L+R mix)

Speakesr In - IN (L; R; L+R mix)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audison srx 1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info