777537
16
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
Open/close
If the projector is the new one. Please read “projector install” chapter. Placed the projector. Connect the
powerwire and the signelwire. The operation as follow:
Open operation
1. Before use the remoter. Put in two 7 size battery in it.
2. Open the power switch on the backboard. The power
light begin to flash.
3. Press the power key on the remote control or panel.
The indicator light turn light.
4. Alter 2 second. the projector lamp begin work. began appear unclear white light on the screen.
After 2 minute projector begin work ..
5. For the new projector. When the frist time to use. maybe will appear image unclear or trapezoid
distortion . please rend “image adjustment" chapter.
6. After the image is clear. then you can watch program. during watching. you also can setup the
system parameter. please read “menu setting" chapter»
Close operation
1. During use the projector. press “power” key. can let the projector switch to situation.
2. After inter into stay situation. the projector under auto protect, auto release hot. the indicator light
is ase situation. but here. the projector is under auto protect situation. not accept any order. if
need to startup again . must wait for nished the release hot .
Image Adjustment
When you use the projector first time. It normally will appear image faintness or the image is trapezoid. It is
the reason of lens focus or trapezoid correction. Please follow the step the correction:
Focus correction
Turn the lens into the projector (1), then turn it out slowly (2), at the same time looking at the resolution
point care when the image is very clearly (take the middle area of the image), it is the best situation of the
lens.
Note: When you replace the projector from a cold to a warm environment water vapour might occur. Don't
turn the projector on when this occurs but wait until the vapour has disappeared.
Keystone correction
If a projected picture has keystone distortion, correct image with Keystone adjustment. The image becomes
trapezoid shape when the screen or project is not level. Please reposition the projector to improve its angle
to the screen. However, the circumference of the image may not be focused.
If not able to use K. correction function to correct the trapezoid distortion. Please reduce of the projector to centre the screen vertically.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Auna 10005061 EH3WS wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info