Bedienungsanleitung Avenli 17795 (Seite 5 von 21) (Deutsch, Englisch, Holländisch)

765058

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

OP1-20-GB(V3) OP1-20-GB(V3)

PART4-SET UP THE POOL

Step1. ACCOUNT FOR ALL PARTS.

Remove all the parts from the carton(s) and place them on the ground in the location where they are to be assembled

Check each part according to “PART REFERENCE” .Make sure all the pieces to be assembled are accounted for.

IMPORTANT: Do not start assembly if any pieces are missing. For replacement pieces call the Consumer Service

telephone number in your area.

The number of persons required for installation: 2 adult at least.

Total installation time except the time for site preparation and water lling :

10 minutes for size Ф8’x25”/Ф10’x30”/Ф12’x30”/Ф12’x33”/Ф6’ x 29”

30 minutes for size Ф14’ x 33”/Ф13’ x 33”/Ф15’ x 33”

Step2. INSTALL DRAIN VALVES COVER AND STOPPER

Make sure that outer drain plug is inserted into the outer drain cap and drain valve cover is screwed on tightly.Plug the con-

nection holes with the stoppers. (The out drain plug changes according to different size of pool.)

STOPPER Out Drain Plug A Out Drain Plug BDrain Vavle Cover

Step3. INFLATE THE TOP RING

Keeping the top ring in the middle of the pool (the top ring must be kept inside the circumference of

the pool bottom.)

VERY IMPORTANT: The top ring should be lled to approx. 80% capacity only. DO NOT attempt

to inate the ring past this point.Excessive ination of the top ring can cause the ring to burst or

cause damage to the ring’s seams.

80%

WARNING:

Do not leave pool unattended while lling with water.

WARNING:

If more than 1~2 inches of water collects on any one side before you

start lling in the center.The pool is not level enough, and must be corrected! You

shall pull out the drain plug, release the water completely, disassemble the pool

completely,locate the pool on a plane surface, repeat set up instruction.

WARNING:

DO NOT OVERFILL as this could cause the pool to collapse.In times of

heavy rainfall you may need to empty some of the water to ensure the level is correct.

PART5-FILL THE POOL WITH WATER

1. Make sure the drain tting is plugged securely and the cap

is in place. Start lling the pool with water. After about 1-inch of

water is on the bottom, stop lling and smooth wrinkles out of the

bottom of the pool. Pull the outer wall out from the top edge, all

around the bottom of the pool, so that it lls evenly.

2. Contineue lling the pool until water level.

WARNING:

Do not let your children stand at downfold and face the water outlet

during the drainage. The water current may sweep your children.

WARNING:

Pool should be stored at places where is cool and dry, with no sharp

object surround, or no heavy objects lying above, which may cause damage to the

pool.

PART6-WINTERISING AND LONG-TERM STORAGE

Step1. If you have a lter pump, make sure that the electricity source to the lter pump has been disconnected.

Step2. Check to ensure that the out drain plug is rmly inserted on the inside of the pool.

Step3. Attach your garden hose to the drainage valve connector, and placing the other end of the hose in an area where the

water can drain safely, such as a storm drain or street gutter. Remember that because water always nds its own level, the end

of the hose must be lower in elevation than the pool to ensure complete drainage.

Step4.If you have a lter pump, insert the stopper into the inlet and outlet xtures, on inside of pool, and then disconnect the

lter pump hoses.

Step5. Attach the drainage valve connector to the drain outlet by turning connector in a clockwise direction.

Step6. Open the out drain plug on the inside of the pool and the water will begin to drain immediately.

Step7. Disconnect the hose and drainage valve connector when nished.

Step8. Replace the out drain plug on the inside of the pool.

Step9. Be sure that the pool liner is completely dry before folding the pool for long-term storage. Leaving the pool exposed to

sunlight for a few hours will clean and speed the drying process and make it easier to fold the pool for storage. (Never attempt

to fold or stow a pool that is not completely dry as this could lead to a proliferation of mold or mildew build-up during the time

the pool is in storage.)

Step10. Remember, proper off-season storage is critical to protect your investment in your pool.(espeically in winter) Once

drained and dry, your pool should be carefully folded and wrapped in a ground cloth (if available) or other similar protective

tarp-like material. The pool and all applicable accessories such as the pump, cover, ground cloth, ladder, hoses, clamps, and

hardware should be kept together and stored indoors, in a reasonably warm, dry and weatherproof location.

Before folding, it’s better to dry all parts and pool completely by lying them in the sun

for one hour or so.(PIC.1). And then, spread some talcum powder to prevent the vinyl

from sticking together.

FOLDING INSTRUCTION

Step1. Please fold the protrusion sides inside to gain rectangle shape.(PIC.2).

Step2. Fold each half of the rectangle to gain a smaller rectangle shape.(PIC.3).

Step3. Fold each ends backwards. (PIC.4).

Step4. Fold the rest ends together to create an ultimate rectangle one.(PIC.5).

TIPS1. Please remove air inside to make the folded pool thin and at during each folding.

TIPS2. The original packing can be used for storage.

PART5-FILL THE POOL WITH WATER

80 %

Avenli 17795 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info