661191
13
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
7. Maintenance
Changing the Needle(s)
Note: #365A017 needle is a very special needle and is
exclusive for the Embellisher machine. See your Baby
Lock retailer for replacement needles.
Caution: When changing needle(s), unplug the power cord
from the electrical outlet.
1. Open lamp cover and remove finger guard. (see page
4.)
2. Turn the handwheel until the needle bar is at the highest
position and then lower the cloth presser lifter lever.
3. Lower the cloth presser to the lowest position by turning
the cloth presser height adjusting screw clockwise.
4. While holding the needle clamp holder, loosen the nee-
dle clamp fixing screw by turning the large 2mm allen
screwdriver counter-clockwise.
5. Lower the needle clamp holder slowly into the cloth
presser. The needles must not touch the cloth presser.
Tilt the needle clamp holder slightly forward and remove
it from the machine.
6. To remove the individual outer needles, loosen the
needle fixing screw on the needle clamp holder by turn-
ing the small 1.5mm allen screwdriver counter-clock-
wise and remove the needle(s) by using tweezers.
Insert the new needle(s) until the top of the needle
touches the top of the needle hole. Tighten the needle
fixing screw with the small 1.5mm allen screwdriver by
turning the allen screw clockwise. Center needle is
replaced by loosening the center needle fixing screw,
replace needle and then tightening the screw.
Note: #365A017 needles do not have a front or back,
therefore, you can insert the shank of the needle in any
direction.
7. When replacing the needle clamp holder, make sure the
needle bar is in its highest position. Tilt the needle clamp
holder so the needles will slide into the cloth presser
and slide the clamp up onto the needle bar until the red
mark on the needle bar and needle clamp holder align.
Tighten the needle clamp fixing screw by turning with
the large 2mm allen screwdriver clockwise. Adjust the
cloth presser to desired height.
8. Replace finger guard and close lamp cover.
Use #365A017 needles for the Embellisher machine.
Do not use any other type of needles
Allen screwdriver
1.5mm
Needle clamp
fixing screw
Needle fixing
screws
Needle clamp
fixing screw
Red alignment
mark
Needle plate
Allen screwdriver
2mm
10
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Baby Lock Embellisher - EMB12 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info