614493
51
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
T
R
O
U
B
L
E
S
H
O
O
T
I
N
G
49
Troubleshooting Continued
Dos and Don'ts
Needle threading difficulties:
1. Is the needle threader selector at the appropriate setting?("R" for right needle, "L" for left needle.)
Looper threading difficulties:
1. Is the looper threader selector at the appropriate setting?(Left threading port for "U" upper looper, right
threading port for "L" lower looper.)
2. Is the thread end in the proper threading port?
3. Is at least 1 inch (2.5cm) of the thread end in the threading port?
4. Is there at least 18 inches (40cm) of loose thread beyond the thread guide above the threading port?
5. Is there a kink or twist in the 18 inch (40cm) of thread to restrict the flow into the threading port?
6. Is the thread caught to prevent going through the loopers?
Poor Cutting:
1. Are the cutting blade(s) dull?
2. Have you sewn over a straight pin?
3. Is the cutting blade in the locked position?
4. Have the cutting blades been improperly replaced?
5. Is the fabric being pulled from the rear of the machine while sewing?
1. Always be aware of the needle's up-and-down movement, and do not turn your attention from the
machine while it is running.
2. When changing the needle, the presser foot or any other parts, always disconnect the machine by turn-
ing the power switch to OFF.
3. Do not place anything on the foot controller, or the machine will start inadvertently and the controller or
motor can be burn out.
4. The maximum permissible power for the light bulb is 15W/110V, or 15W/230V over 200 voltage coun-
try.
5. When using your serger for the first time, place a fabric scrap under the presser foot and run the
machine without thread for a few minutes. Wipe away any oil that appears.
6. Do not pull fabric from the rear of the machine. Such action can damage the looper mechanism.
7. To prevent possible injury, always avoid body contact with any moving parts and the machine mecha-
nism.
8. NEVER sew over pins.
Special Caution: Unplug the power cord from the electrical outlet when the machine is not in use.
0001.qxp:AT-2En Ta.qxd 09/05/29 13:23 Page 51
51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Baby Lock Imagine BLE 1AT-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Baby Lock Imagine BLE 1AT-2

Baby Lock Imagine BLE 1AT-2 Bedienungsanleitung - Holländisch - 59 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info