Bedienungsanleitung Bartscher Deltamat TF 50 LR (Seite 7 von 18) (Englisch)

554347

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

page 25

INSTALLER SECTION

ATTENTION:

At the end of installation make sure to remove the parts of this booklet relevant to the installer,

for future consultation.

1. MACHINE INSTALLATION

1.1 Receipt of the appliance

After removing the packing, ensure that the appliance has not been damaged in transport.

If it has, inform the retailer. If safety has been compromised, do not install the machine. For

disposal of the packing, see ch.8.

1.2 Water connection

Connect the machine's water supply with an interrupt valve capable of quickly and completely

shutting off water intake.

Make sure that the water supply pressure comes within the values given in the Table 1.

If it is less than 2 bar dynamic pressure (200 kPa) a pressure pump must be installed to

guarantee optimal machine operation (by request, the dishwasher can be supplied with a

pump).

If, however, the water supply pressure is greater than 400 kPa, a pressure reducing device

must be installed.

For water with average hardness greater than 10°Fr., a water softener must be used.

This will result in cleaner dishes and longer life of the appliance.

By request, the machine can be equipped with a water softener (see chap. 5.4).

All damages caused by the hydraulic limestone (calcareous water higher-up than 10°F and

without watersoftner) are not are not covered by warranty.

In order to ensure the optimum performance, the water supply temperature must come

within the range given in table 2.

Each machine is provided with a rubber tube with a ¾" threaded attachment for water

lling.

Connect the emptying tube, supplied with the appliance, to the union elbow located under

the tub so that water ows freely. If it is not possible to empty the water at a level lower

than the drain of the appliance, it is advisable to install an emptying pump, which can be

provided by request.

The emptying tube should always be connected to a siphon to prevent odor back-up from

the screen.

1.3 Electrical connection

The electrical connection must be made according to current technical standards.

Ensure that the mains voltage corresponds to the value given on the machine dataplate.

Install a suitable omnipolar thermal magnetic circuit breaker, dimensioned according

to absorption, with a contact opening of at least 3 mm.

This circuit breaker must be exclusively used for this purpose and installed in the

immediate vicinity.

Make sure that the electrical systems are suitably earthed.

On the back of the appliance there is a terminal marked with the symbol (see Pict.

1), which is provided for equipotential connection between different appliances (see

electrical safety standards).

FOR APPLIANCES USING A THREE-PHASE POWER SUPPLY, FOLLOW THE

INSTRUCTIONS AND WIRING DIAGRAM ATTACHED TO THE APPLIANCE.

ATTENTION TO CORRECT SENSE OF TRI-PHASES PUMPS ROTATION (if

present).

pict. 1

Pressure

Table

Min. Max.

kPa kPa

Static Pressure

250 400

Dynamic Pressure

200 350

Water hardness

2°f 10°f

O supply temperature table

Machine upon

request

Standard Macchine

from catalogue

O Cold H

O Hot

5°C ≤ t < 50°C 50°C≤ t ≤ 60°C

table 2table 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bartscher Deltamat TF 50 LR Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bartscher Deltamat TF 50 LR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info