Bedienungsanleitung BeamZ DMX 016 Channel Console (Seite 9 von 11) (Deutsch, Englisch, Holländisch, Spanisch)

506088

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

2. Program

Press program button for more than one second to enter program mode, the matching indicator is lit. Press

pattern ▲ to select desired pattern. Make a setting by menas of fader 1 – 8 and latch button and press program

button once to store the setting as a new step. Make a new setting and press program once again. If you have

entered all steps press shift + endstep button together to define the last step.

Example:

1. Press programm button for more than one second to enter program mode. The matching incicator is lit.

2. Press pattern ▲ or pattern ▼ and step ▲ or step ▼ till the display shows 11:01

3. Slide fader 1 to up position and the other faders to down. Press latch 9-16 to turn all matching indicators off.

After this setting press programm button once, now the LCD would show 11:02

4. Slide fader 2 to up position, others down, press latch 9-16 to turn all matching indicators off. After this

setting press programm button once again. The display shows 11:03

5. repeat steps one and two for all other faders till the display shows 11:09. Slide all faders to down position

and press latch 9-16 to turn channel 9 indicator on and the other indicators off. Press programm button

once. The display now shows 11:10

6. Continue your setting till the display shows 11:17, now press step button to alert 11:17 to 11:16

7. press shift + end step to define the 16th step to be the last step. Now the pattern is complete.

3. Assign program

There are 16 assign for the levels set by fader 1 to 8 and latch 9-16 buttons.

Example:

To assign CH1 to CH9 full on, and CH10 to CH16 blackout to flash 1 button, follow the next steps.

1. Press assign button for more than one second to enter assign program mode. The matching indicator is lit.

2. Slide fader 1 to 8 to up position, press latch 9 button to turn CH9 indicator on.

3. Press assign button first, then press flash 1 button. All channel indicators flash three times. Now assign one

is complete.

4. Patch setting

In patch mode, you could allocate easily the outgoing DMX channels to your light fixtures

Example:

To allocate 1-16 DMX channels to 16-1 channels, follow next steps.

1. Press patch button for more than one second to enter patch mode, the matching indicator is lit. Press

step ▲ or step ▼ till the display shows 01 in the right two digits.

2. Press pattern ▲ or pattern ▼ till the display shows 16 in the left two digits. Now the first DMX channel is

relocated to the level of the 16th channel.

3. Press step ▲, the display shows 02 on the right side. Press pattern ▼, the display shows 15 in the left two

digits. Now the 2nd DMX channel is relocated to the level of the 15th channel.

4. Follow the settings as specified by step 3 till the 16th DMX channel is relocated to the level of the first

channel. Press patch button for more than one second to leave patch mode. The matching indicator is off.

5. Run pattern in cross mode

In cross mode, the patterns are executed step by step by sliding the master fader up and down repeatedly.

1. In chase mode, press shift + cross setup, the cross on indicator is lit.

2. Slide the master fader to top position, press cross button to enter cross mode. The A indicator is lit.

3. Press pattern ▲ or pattern ▼ till the display shows 11:01

4. Turn the level knob to maximum, now the A indicator is full on.

5. Slide the master fader from top to bottom position, the patterns to be executed by one step and the step

counter to be increased by one (display shows 11:02). Now the channel 1 indicator is full on and A is off, B is

full. Slide the master fader up, the B indicator is decreased and the A indicator is increased in intensity. The

channel 2 indicator is increased and the channel 1 indicator is decreased in intensity. When master fader is

in top position, the B indicator is off and the A indicator is full on. The channel 2 indicator is full on and the

channel 1 indicator is off. The step counter is increased by one (display shows (11:03).

6. Repeat these settings to execute the pattern step by step.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BeamZ DMX 016 Channel Console Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info