Bedienungsanleitung Behringer VS1220 (Seite 4 von 9) (Englisch)

660569

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

4 EUROLIVE VS1520/VS1220F/VS1220 User Manual

1. Before You Get Started

1.1 Shipment

Your VS series loudspeaker was carefully packed at the assembly plant to assure

secure transport. Should the condition of the cardboard box suggest that damage

may have taken place, please inspect the unit immediately and look for physical

indications of damage.

◊ Damaged equipment should NEVER be sent directly to us. Please inform

the dealer from whom you acquired the unit immediately as well

as the transportation company from which you took delivery.

Otherwise, all claims for replacement/repair may be rendered invalid.

◊ Please always use the original packaging to avoid damage due to

storage or shipping.

◊ Never let unsupervised children play with the loudspeaker or

with its packaging.

◊ Please dispose of all packaging materials in an environmentally

friendly fashion.

1.2 Online registration

Please register your new BEHRINGER equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warranty carefully.

Should your BEHRINGER product malfunction, it is our intention to

have it repaired as quickly as possible. To arrange for warranty service,

please contact the BEHRINGER retailer from whom the equipment was

purchased. Should your BEHRINGER dealer not be located in your vicinity,

you may directly contact one of our subsidiaries. Corresponding contact

information is included in the original equipment packaging (Global Contact

Information/European Contact Information). Should your country not be listed,

please contact the distributor nearest you. A list of distributors can be found in

the support area of our website (http://behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eciently.

Thank you for your cooperation!

1.3 Basic operation

Using the VS series loudspeakers is easy and intuitive. Simply follow these steps

to achieve the best possible sound:

1. Plug the line-level outputs from a sound source such as a mixer or stereo

system into a power amp of appropriate size (see 4.2 Power amp rating).

Make sure the sound source and amplier are turned o.

2. Using ¼" TS speaker cables, plug the power amp output into the ¼" input on

the back of the speaker. DO NOT use instrument cables (i.e., guitar cords) for

this connection!

3. If using a pair of VS loudspeakers, run the amp in stereo operation.

If using just one loudspeaker, mono operation is preferable.

4. If using four or more loudspeakers, there are a few ways to make the

connections. The rst is to use two power amps, one for each pair. Another is

to connect the rst pair of loudspeakers in normal stereo operation, then use

the ¼" output jacks on the back of the loudspeakers to link the second pair

of loudspeakers. This way each channel on the power amp is driving two

loudspeakers. Make sure that the wattage and ohm rating are appropriate

for this situation.

 Caution

Never connect multiple power amps to one loudspeaker. Doing so could cause

the very fabric of reality to unravel, sending the entire universe into oblivion.

Worse yet, it could destroy your ampliers and loudspeaker.

5. Turn the sound source on (mixer, stereo, etc.).

6. Make sure the volume/gain control on the power amp is turned all the way

down, and then turn the power on.

7. Activate the sound source, whether it is playing music from a CD player or

speaking into a microphone, and adjust the levels. Gradually raise the power

amp volume level to desirable level. If distortion occurs, turn the power

amp volume down. Should the problem persist, make sure distortion is not

occurring at the sound source. If you reach the desired volume level by barely

turning up the power amp level/gain, turn the sound source output down to

allow the power amp to push the speakers more.

8. Rock ‘n Roll!

2. Connections

(1)

Fig. 2.1: Connector panel

(1) The VS series features two parallel ¼" TS loudspeaker inputs. You can

connect one of the connectors to the output on your power amp and tap

into the signal from the amp on the second connector, in order, for example,

to feed this signal into an additional loudspeaker.

strain relief clamp

sleeve

tip

sleeve

(ground/shield)

Unbalanced ¼" TS connector

tip

(signal)

Fig. 2.2: ¼" TS loudspeaker connector

◊ ATTENTION: Never connect the output signals of different power

amps to both parallel inputs at the same time. This may permanently

damage your equipment.

◊ When several loudspeakers are wired in parallel, the overall impedance

ZT to be handled by the power amp can be calculated, as shown here,

from the individual impedance values of the connected speakers:

⁄Z



⁄Z





Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Behringer VS1220 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Behringer VS1220

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info