660568
4
Zoom out
Zoom in
Vorherige Seite
1/9
Nächste Seite
4 EUROLIVE VS1520/VS1220F/VS1220 User Manual
1. Before You Get Started
1.1 Shipment
Your VS series loudspeaker was carefully packed at the assembly plant to assure
secure transport. Should the condition of the cardboard box suggest that damage
may have taken place, please inspect the unit immediately and look for physical
indications of damage.
Damaged equipment should NEVER be sent directly to us. Please inform
the dealer from whom you acquired the unit immediately as well
as the transportation company from which you took delivery.
Otherwise, all claims for replacement/repair may be rendered invalid.
Please always use the original packaging to avoid damage due to
storage or shipping.
Never let unsupervised children play with the loudspeaker or
with its packaging.
Please dispose of all packaging materials in an environmentally
friendly fashion.
1.2 Online registration
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to
have it repaired as quickly as possible. To arrange for warranty service,
please contact the BEHRINGER retailer from whom the equipment was
purchased. Should your BEHRINGER dealer not be located in your vicinity,
you may directly contact one of our subsidiaries. Corresponding contact
information is included in the original equipment packaging (Global Contact
Information/European Contact Information). Should your country not be listed,
please contact the distributor nearest you. A list of distributors can be found in
the support area of our website (http://behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and eciently.
Thank you for your cooperation!
1.3 Basic operation
Using the VS series loudspeakers is easy and intuitive. Simply follow these steps
to achieve the best possible sound:
1. Plug the line-level outputs from a sound source such as a mixer or stereo
system into a power amp of appropriate size (see 4.2 Power amp rating).
Make sure the sound source and amplier are turned o.
2. Using ¼" TS speaker cables, plug the power amp output into the ¼" input on
the back of the speaker. DO NOT use instrument cables (i.e., guitar cords) for
this connection!
3. If using a pair of VS loudspeakers, run the amp in stereo operation.
If using just one loudspeaker, mono operation is preferable.
4. If using four or more loudspeakers, there are a few ways to make the
connections. The rst is to use two power amps, one for each pair. Another is
to connect the rst pair of loudspeakers in normal stereo operation, then use
the ¼" output jacks on the back of the loudspeakers to link the second pair
of loudspeakers. This way each channel on the power amp is driving two
loudspeakers. Make sure that the wattage and ohm rating are appropriate
for this situation.
Caution
Never connect multiple power amps to one loudspeaker. Doing so could cause
the very fabric of reality to unravel, sending the entire universe into oblivion.
Worse yet, it could destroy your ampliers and loudspeaker.
5. Turn the sound source on (mixer, stereo, etc.).
6. Make sure the volume/gain control on the power amp is turned all the way
down, and then turn the power on.
7. Activate the sound source, whether it is playing music from a CD player or
speaking into a microphone, and adjust the levels. Gradually raise the power
amp volume level to desirable level. If distortion occurs, turn the power
amp volume down. Should the problem persist, make sure distortion is not
occurring at the sound source. If you reach the desired volume level by barely
turning up the power amp level/gain, turn the sound source output down to
allow the power amp to push the speakers more.
8. Rock ‘n Roll!
2. Connections
(1)
Fig. 2.1: Connector panel
(1) The VS series features two parallel ¼" TS loudspeaker inputs. You can
connect one of the connectors to the output on your power amp and tap
into the signal from the amp on the second connector, in order, for example,
to feed this signal into an additional loudspeaker.
strain relief clamp
sleeve
tip
sleeve
(ground/shield)
Unbalanced ¼" TS connector
tip
(signal)
Fig. 2.2: ¼" TS loudspeaker connector
ATTENTION: Never connect the output signals of different power
amps to both parallel inputs at the same time. This may permanently
damage your equipment.
When several loudspeakers are wired in parallel, the overall impedance
ZT to be handled by the power amp can be calculated, as shown here,
from the individual impedance values of the connected speakers:
Z
T
1
⁄Z
⁄Z
++

=
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer VS1220F wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer VS1220F

Behringer VS1220F Bedienungsanleitung - Deutsch - 9 seiten

Behringer VS1220F Bedienungsanleitung - Holländisch - 9 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info