542740
9
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
16
ENGLISH
XENYX 1622FX/1832FX/2222FX/2442FX User Manual
17
wired in a balanced conguration. In case of doubt, contact
the microphone manufacturer!
Connect microphones before you switch on the
phantom power supply. Please do not connect
microphones to the mixer (or the stagebox/wallbox)
while the phantom power supply is switched on. In
addition, the monitor/PA loud-speakers should be
muted before you activate the phantom power supply.
After switching on, wait approx. one minute to allow
for system stabilization.
Caution! Please also note the information given in
chapter 6.2.1 Audio connections”.
SERIAL NUMBER
Please note the important information on the serial number
given in chapter 1.3.3.
INSTALLATION6.
Rack mounting6.1
The packaging of your mixing console contains two 19" rack
mounts for installation on the side panels of the console.
Before you can attach the rack mounts to the mixing
console, you need to remove the screws holding the left
and right side panels. Then, use these screws to fasten the
two rack mounts, each specically to one side. With the
rack mounts installed, you can mount the mixing console
in a commercially available 19" rack. Be sure to allow for
proper air ow around the unit, and do not place the mixing
console close to radiators or power amps, so as to avoid
overheating.
Only use the screws holding the mixing console side
panels to fasten the 19" rack mounts.
Cable connections6.2
You will need a large number of cables for the various
connections of the console. The illustrations below show the
wiring of these cables. Be sure to use only high-grade cables.
Fig. 6.1: Foot switch connector
Audio connections6.2.1
Please use commercial RCA cables to wire the 2-track inputs
and outputs.
You can, of course, also connect unbalanced devices to
the balanced input/outputs. Use either mono plugs, or use
stereo plugs to link the ring and shaft (or pins 1 & 3 in the
case of XLR connectors).
Fig. 6.2: XLR connections
strain relief clamp
sleeve
tip
sleeve
pole 1/ground
tip
pole 2
The footswitch connects both poles momentarily
1/4" TS footswitch connector
input
output
For unbalanced use, pin 1 and pin 3 have to be bridged
1 = ground/shield
2 = hot (+ve)
3 = cold (-ve)
12
3
1
2
3
Balanced use with XLR connectors
Caution! You must never use unbalanced XLR
connectors (PIN 1 and 3 connected) at the MIC input
jacks if you want to use the phantom power supply.
Fig. 6.3: 1/4” mono plug
Fig. 6.4: ¼" stereo plug
Fig. 6.5: Insert send/return stereo plug
Fig. 6.6: Stereo plug for headphones connection
Strain relief clamp
Sleeve
Tip
Sleeve
(ground/shield)
Unbalanced ¼" TS connector
Tip
(signal)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Balanced 1/4" TRS connector
ring
cold (-ve)
tip
hot (+ve)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
Connect the insert send with the input and the
insert return with the output of the effects device.
Insert send return 1/4" TRS connector
ring
return (in)
tip
send (out)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
1/4" TRS headphones connector
ring
right signal
tip
left signal
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer Xenyx 2222FX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer Xenyx 2222FX

Behringer Xenyx 2222FX Bedienungsanleitung - Holländisch - 17 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info