656678
8
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
ULTRAZONE ZMX8210
Installation8
Connect the potentiometer to pins V and SHD. Connect the mid
tap to pin C (see Fig. 3.2).
Volume potentiometer
Remote volume control Fig. 3.2:
connection with potentiometer
Alternatively, you can control the volume by using a positive con-
trol voltage of max. 11 V DC. The voltage needs to be inserted
between the pins SHD and C.
When using a voltage source to remote control the vol- +
ume level, make sure that the control voltage does not
exceed 11 V DC or else your unit could be damaged.
Selecting stereo channels 7 and 8
To select the stereo channels 7 and 8, you need a push-button
switch and optionally two LEDs.
Connect the push-button switch to pins SHD and SEL. You can
add two LEDs to indicate the selected channel. They have to be
connected in parallel with a reverse polarity between the pins IND
and SHD (see Fig. 3.3).
Control LED CH 8
Control LED CH 7
Channel select switch
Connection with push-button switch and two LEDs for Fig. 3.3:
channel selection
Basic operation3.2
Using the ZMX8210 is easy to learn and is very similar to using a
standard mixer. Complete the following steps:
Hook up the unit as described in Chapter 3.1.1)
Adjust the LEFT, RIGHT and AUX LEVEL knobs 2) [17] to center
position and turn the LEVEL knobs {5} of each channel fully
to the left.
Turn on the ZMX8210 and the other devices you want to use 3)
(amplier and loudspeakers last).
Apply an audio signal (line or microphone signal) to an input 4)
channel.
Press the +48 V push-button switch 5) {2} in case you want to
use a capacitor microphone.
Press the push-button switches L, R and AUX 6) {3} to select
the buses to which the input signals are sent.
Turn the LEVEL knob of the corresponding channel to the 7)
right until
you have reached the required volume level =
or the 0 db LED glows continuously. =
If the CLIP LED lights up, you need to adjust the level by slowly
turning the knob to the left. For especially strong input signals, use
the PAD push-button switch {1} to attenuate the signal further.
Repeat steps 4 to 7 with additional signal sources. Use chan-8)
nels 7 or 8 for stereo signal sources.
In case you are using a microphone, press the MIC LOW CUT 9)
push-button switch [11] to reduce low-frequency rumble such
as subsonic noise.
Press the EQ ON push-button switch 10) [14] and adjust the LOW,
LOW MID, HIGH MID and HIGH knobs of the equalizer section
(15) to modify the sound.
Use the LEVEL knobs of the LEFT, RIGHT and AUX buses 11)
[17] to adjust the volume level of the OUT L, OUT R and AUX
outputs (zones).
Installation4.
Rack mounting4.1
The unit requires the height of 1 U to t within a 19" rack. Please
make sure to provide approximately 4" of space for the connec-
tors on the rear panel. Please use M6 rack screws and nuts when
rack-mounting the unit.
Audio connections4.2
The ZMX8210 connections are Euro-type connectors. You require
special PCB connectors for the cabling. You can purchase the
connectors at well-assorted electronics retailers. The ZMX8210
connectors' pin assignment is printed on the rear panel of the unit.
Alternatively, refer to the following diagrams.
INPUTS / AUX / OUT R / OUT L
Pin assignment of the INPUTS connectorsFig. 4.1:
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Behringer ZMX8210 Ultrazone wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Behringer ZMX8210 Ultrazone

Behringer ZMX8210 Ultrazone Bedienungsanleitung - Deutsch - 11 seiten

Behringer ZMX8210 Ultrazone Bedienungsanleitung - Holländisch - 9 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info