Bedienungsanleitung BEKO WML 50821 (Seite 3 von 52) (Englisch, Französisch)

550069

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

kilograms. Place the product on a solid and flat

floor that has sufficient load carrying capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the packaging

reinforcement. Remove the packaging reinforcement

by pulling the ribbon.

Removing the transportation locks

 Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

Remove the transportation safety bolts before

operating the washing machine, otherwise, the

product will be damaged.

1. Loosen all the bolts with a spanner until they

rotate freely (C).

2. Remove transportation safety bolts by turning

them gently.

3. AttachtheplasticcoverssuppliedintheUser

Manual bag into the holes on the rear panel. (P)

Keep the transportation safety bolts in a safe

place to reuse when the washing machine

needs to be moved again in the future.

Never move the product without the

transportation safety bolts properly fixed in

place!

Connecting water supply

 Thewatersupplypressurerequiredtorunthe

productisbetween1to10bars(0.1–10MPa).

Itisnecessarytohave10–80litersofwater

flowing from the fully open tap in one minute

to have your machine run smoothly. Attach a

pressure reducing valve if water pressure is

higher.

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot

water valve before operating the product.

(Applies for the products supplied with a blind

stopper group.)

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

supplied with a blind stopper group.)

Models with a single water inlet should not be

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

 Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1. Connect the special hoses supplied with the

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,blue

hose(right)(max.25ºC)isforcoldwaterinlet.

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise,yourlaundrywillcomeouthotatthe

end of the washing process and wear out.

2. Tighten all hose nuts by hand. Never use a

wrench when tightening the nuts.

3. Openthetapscompletelyaftermakingthe

hose connection to check for water leaks at the

connectionpoints.Ifanyleaksoccur,turnoff

the tap and remove the nut. Retighten the nut

carefully after checking the seal. To prevent water

leakages and damages caused by them, keep

the taps closed when the machine is not in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

Your house will be flooded if the hose comes out

of its housing during water discharge. Moreover,

there is risk of scalding due to high washing

temperatures! To prevent such situations and to

ensure smooth water intake and discharge of the

machine, fix the end of the discharge hose tightly

so that it cannot come out.

• Thehoseshouldbeattachedtoaheightofat

least40cm,and100cmatmost.

• Incasethehoseiselevatedafterlayingitonthe

floorlevelorclosetotheground(lessthan40cm

above the ground), water discharge becomes

more difficult and the laundry may come out

excessively wet. Therefore, follow the heights

described in the figure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BEKO WML 50821 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info