648619
16
Zoom out
Zoom in
Vorherige Seite
1/18
Nächste Seite
15 010508A-1
CALLER ID UNIT TROUBLESHOOTING TABLE
SYMPTOM SOLUTION
The Caller ID
LCD panel is
blank
Check the batteries for proper installation.
If the batteries are weak or dead, replace with new batteries
(alkaline batteries are recommended). Please refer to the
“Battery Installation” section of the users manual for more
details.
Check the connection of the AC adaptor.
The Caller ID
LCD panel does
not show the
callers name
and/or phone
number
The Caller ID unit will not function until you have Caller ID
service provided by your local phone company. Call your
local phone company to have Caller ID installed on your
telephone line.
Check your telephone line connections. Refer to the section
“INSTALLATION” of the manual for details.
If you picked up the phone before
the second ring, the caller
information will not
be correctly received. If you have a
telephone answering device (TAD) connected with the unit, set
the TAD to answer after two rings or more.
If it is a blocked call or an out-of-area call, the callers name
and/or phone number will not appear on the display. Please
refer to the “Receiving Caller ID Information” section of the
user’s manual for more details.
If only the callers phone number appears on the display, it
may
be a Single Data Message Format (SDMF) call, as opposed to a
Multiple Data Message Format (MDMF) call. Please refer to
the Glossary section of the users manual for definitions.
“LINE
ERROR”
On rare occasions, the Caller ID information sent by the
telephone company may have an error in the transmission.
This is not the fault of your Caller ID unit. It can only capture
and store the data that was received.
Cannot delete
call records in
memory
The DELETE button must be pressed twice briefly to delete a
single call record. To delete all call records, press and hold the
DELETE button for as least 5 seconds. Please refer to the
“ERASING A CALL/ALL CALLS” section of the manual for
more details.
No Data Sent
On rare occasions, Caller ID information sent by the telephone
company may be too weak to be detected by the Caller ID.
This is not the fault of the Caller ID unit; it can only capture
and store the digital data that was received.
This message also appears when the Callers local phone
company does not have Caller ID service available.
TELEPHONE UNIT TROUBLESHOOTING TABLE
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bell phones Big Button Plus 20270 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info