Bedienungsanleitung Bell Shell (Seite 3 von 8) (Englisch, Französisch, Spanisch)

772318

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

1ATTACH MOUNT ONTO BIKE FRAME

1. Remove four (4) screws from back of

mount using 5mm Allen wrench.

2. Place front of mount around seat

tube of bike. Insert back of mount

to front of mount, insert screws.

Do not fully tighten. Do not place

around brake and derailleur cable

and housing.

CLICK RACK INTO MOUNT

1. Slide the ends of the carrier rack into the top holes on the mount. Once secured,

you will hear a click. This means the carrier rack is secured to the mount.

2. Slide the loose mount up or down until there is about 6 inches between rear wheel

and bottom of carrier. Be sure mount is centered along rear wheel facing forward.

3. Tighten the screws on the mount until mount will not slip up, down, or side to side.

4. Tighten fasteners securely, and check them frequently.

EASY, 3-STEP INSTALLATION

WARNING

Do not modify carrier rack or bicycle. If carrier rack will not t on your bicycle, consult your local bicycle dealer or

call our Customer Service at 1.800.456.BELL for assistance.

SEAT PAD INSTALLATION FOOT REST INSTALLATION

FOOT STRAP ATTACHMENT

1. Loop one piece of Velcro® through each foot rest and

attach back onto itself.

2. Insert top hooks of foot rests into opening along leg. Must

be at least three notches from bottom. Push to lower tabs

through respective opening and click into place. Lower

hook tabs need to be slightly lifted when inserted into slot.

Place seat pad into bottom of child carrier. Thread retention

harness through seat pad. Insert all four seat pad plugs into the

bottom of the child carrier.

To insert foot rest, insert top hook into preferred height. Slide

bottom tab into slot and pinch both together at the same time

while pushing the foot rest into place. Pull at them gently to

ensure they are secured properly. To remove foot rest, pinch

the hook and tab at the same time and pull up, freeing the

bottom tab. Then pull the top hook free.

• Use harness slots at

child’s shoulders.

• Shoulder straps should t snugly –

so that only one nger can t

between harness and shoulder.

• Ensure top of chest clip is

positioned at armpit level.

• Ensure harness forms the

shape of a V.

• Connect each buckle end and

click to secure.

• To release, pinch each side

of buckle and pull apart

buckle ends.

WARNING

Child can fall out of child carrier if harness is not correctly

fastened and adjusted.

RETENTION HARNESS:

3-POINT HARNESS

REFLECTOR INSTALLATION

To install the reector, remove backing paper on the reector

and place the sticky side onto the hexagonal molded imprint on

the back center of the child carrier. Press to adhere.

4 | English 5 | English

ATTACH RACK TO CARRIER

1. Turn the carrier upside down. Insert

suspension rack bars through holes

as shown below.

2. Insert the locking pin through the

holes under the carrier with the lever

in the unlocked position until it snaps

into place.. Turn the pin 180 degrees

untill it snaps into the locked position.

UNLOCKED LOCKED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bell Shell Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info