214407
35
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
35
Additional information
English
Troubleshooting
Problem Cause Remedy
The projector does
not turn on.
There is no power from the power
cable.
Plug the power cable into the AC inlet on the
rear of the projector, and plug the power
cable into to the power outlet. If the power
outlet has a switch, make sure that it is
switched on. (See page 19)
The power switch is not in the on
position.
Put the power switch in the on position. (See
page 19)
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
The lamp cover is not securely
attached.
Correctly attach the lamp cover. (See page
33)
No picture.
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly. (See page
17)
The projector is not correctly
connected to the input source device.
Check the connection. (See page 17)
The input signal has not been
correctly selected.
Select the correct input signal with the
Source buttons on the remote control or
SOURCE / ENTER on the projector. (See
page 19)
Image is unstable.
The connection cables are not
securely connected to the projector or
the signal source.
Correctly connect the cables to the
appropriate terminals. (See page 17)
Picture is blurred.
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring. (See page 20)
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of this unit if necessary.
(See page 19)
The lens cap is still attached to the
lens
Remove the lens cap. (See page 19)
Remote control does
not work correctly
The batteries are out of power. Replace both of the batteries with new ones.
(See page 9)
There is an obstacle between the
remote control and the projector.
Remove the obstacle. (See page 13)
You are too far away from the
projector.
Stand within 8 meters (26.2 feet) of the
projector. (See page 13)
PE8720-en.book Page 35 Friday, May 13, 2005 5:19 PM
35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für BenQ pe 8720 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von BenQ pe 8720

BenQ pe 8720 Bedienungsanleitung - Holländisch - 38 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info