673667
14
Zoom out
Zoom in
Vorherige Seite
1/17
Nächste Seite
900 Series 932-933 - 14 - Date 25-03-08 UM - Code SC1 - Rev. 0.1
User Manual
5.1 Sharpening device
Every sharpening device is marked with the serial number of the machine.
Only this sharpening device may be used for sharpening.
Usage of other sharpening devices can cause serious injuries or damage the machine. Never use
another sharpening device.
The sharpening device is equipped with 1 stone for sharpening and 1 stone for taking off the burr
(deburring)
Always clean the machine before sharpening, as the stones will then loose their efficiency if they become
contaminated by meat waste and fats. In case this should happen, clean the stones carefully with washing
liquid and a wire brush.
5.2 Mounting the sharpening
device
Open the thickness plate
completely.
Position the carriage in the centre
of the machine
Lift up end piece holder
Mount the sharpening device to
the thickness plate so that the
cone of the sharpening device fits
into the slit on the bottom of the
thickness plate (direction of arrow)
Pull out the pin on top of the
sharpening device in direction of
arrow and move the sharpening
device over the edge of the
thickness plate.
Move the sharpening device with
the pulled out pin to the front in
direction of the blade (direction of
arrow), so that the pin is engaged in the hole of the thickness plate.
The sharpening stones are now in the correct position, i.e. the blade edge is positioned between the two
sharpening stones.
5.3 Sharpening the blade
Switch on the machine
Turn the yellow handwheel of the sharpening device in direction 1. The
sharpening stone is sharpening the blade by being in contact with the blade.
Approximately 15 seconds are enough to sharpen correctly
Switch off the machine
Check if there is a visible burr at the edge of the blade
If not: Sharpen again
Switch on the machine again
To take off the burr turn the yellow handwheel in direction 2. Now both stones are
touching the blade.
Approximately 2 seconds is enough to take off the burr.
Switch off the machine
When the sharpening procedure is completed turn the yellow handwheel to 0.
0
1
2
15 sec.
< 2 sec.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Berkel 932 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info