Bedienungsanleitung Bertazzoni M91V (Seite 4 von 16) (Englisch)

617413

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

TABLE N°1: Adaption to various types of gas APPLIANCE CATEGORY: II2H3+

Burner Types of Gas Pressure Nozzle

Diameter

Rater Capacity Reduced

Capacity

by-pass

Diameter

mbar 1/100 mm. g/h l/h kw kcal/h kw kcal/h 1/100 mm.

Natural G20 20 77 - 95 1 860 0,48 413 34 reg.

Auxiliary Butane G30 30 50 73 - 1 860 0,48 413 34

Propane G31 37 50 71 - 1 860 0,48 413 34

Natural G20 20 117 - 167 1,75 1505 0,6 516 36 reg.

Semi-Rapid Butane G30 30 66 127 - 1,75 1505 0,6 516 36

Propane G31 37 66 125 - 1,75 1505 0,6 516 36

Natural G20 20 129 - 286 3 2580 1,05 903 52 reg.

Rapid Butane G30 30 87 218 - 3 2580 1,05 903 52

Propane G31 37 87 214 - 3 2580 1,05 903 52

Dual Natural G20 20 70 - 76 0,8 688 0,48 413 34 reg.

Inner Butane G30 30 46 58 - 0,8 688 0,48 413 34

Propane G31 37 46 57 - 0,8 388 0,48 413 34

Dual Natural G20 20 110 - 419 4,4 3784 1,8 1548 65 reg.

Outer Butane G30 30 69 298 - 4,1 3526 1,8 1548 65

Propane G31 37 69 293 - 4,1 3526 1,8 1548 65

Natural G20 20 150 - 429 4,5 3870 2 1720 70 reg.

Oven Butane G30 30 95 327 - 4,5 3870 2 1720 70

Propane G31 37 95 321 - 4,5 3870 2 1720 70

BURNER ADJUSTMENT

2) Burner "MINIMUM" adjustment:

Work surface burner adjustment: follow the instructions below to adjust the work surface burner minimum:

1) Light the burner and set the knob to the MINIMUM position (small flame).

2) Remove the knob of the valve that is press fit on the rod of that valve.

3) If the cooker is not equipped with safety valves on the surface burners, insert a small slotted screwdriver into the hole

on the valve rod (Fig. 15) and turn the choke screw to the right or left until the burner flame is adjusted to minimum. If the

cooker is equipped with safety valves, the choke valve is not located in the rod hole, but on the valve body (see fig. 16).

4) Make sure that the flame does not go out when switching quickly from the MAXIMUM to the MINIMUM position.

Oven burner adjustment: follow the instructions below to adjust the minimum:

1) Light the burner setting the knob to the MAXIMUM position.

2) Close the oven door and operate the oven for at least 10 minutes.

3) Set the knob to the MINIMUM position (corresponding to 120°) and then remove it.

4) With a slotted screwdriver turn the choking screw (see figure 17) and, while observing the flame at the same time

through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the

MINIMUM to the MAXIMUM position.

WARNING: The above-mentioned adjustment should be made only with methane gas burners, while for those

operating with liquid gas the screw must be locked at the end in a clockwise direction. The grill

burner always operates at maximum and therefore no minimum adjustment is required.

APPLIANCE ELECTRIC CONNECTION:

The electric connection must comply with the current legal standards and regulations.

Before making the connection, check that:

- The system electrical rating and the current outlets are adequate for the maximum power output of the appliance (see

the label applied to the bottom of the casing).

- The outlet or the system is equipped with an efficient ground connection in accordance with the current legal standards

and regulations. The company will not be responsible for the non-compliance with these instructions.

When the connection to the power supply network is made using an outlet:

- If the power cord is supplied without a plug, apply a standard plug that is suitable for the load indicated on the label.

Connect the wires according to the diagram shown in FIG.18 and check that:

letter L (phase) = brown wire;

letter N (neutral) = blue wire;

ground symbol

= green-yellow wire;

- The power cord must be positioned so that an overtemperature of 75 K will not be reached at any point.

- Do not use reductions, adapters or splitters since they might cause false contacts and lead to dangerous overheating.

When the connection is made directly to the electric network:

- Use a device that ensures disconnection from the mains in which the contacts are opened to a distance that permits

complete disconnection according to the conditions for over-voltage category III.

- Remember that the ground wire must not be interrupted by the circuit-breaker.

- As an alternative, the electric connection can also be protected by a high-sensitivity residual current circuit-breaker.

- It is highly recommended to attach the special green-yellow ground wire to an efficient ground system.

WARNING: If the power cord is replaced, the ground wire (yellow-green) connected to the terminal, should be

longer than the other wires by about 2 cm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bertazzoni M91V Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info