W
Follow all the Safety and Operating Instructions. If you don’t follow this instructions, it may cause overturn, explode the
boat and causes to drowning.
1. Do not exceed the maximum recommended number of persons. Regardless of the number of persons on board,
the total weight of persons and equipment must never exceed the maximum recommended load.
seats / seating spaces provided.
2. When loading the craft, never exceed the maximum recommended load:
distribute loads appropriately to maintain design trim (approximately level).
NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions and personal
effects, any equipment not included in the light craft mass, cargo (if any) and all consumable liquids
(water
3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and used at all
times.
4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and air valves, to
ensure everything is in good condition and tightly secured. Please stop to repair if you find any damage.
5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on
water
6. Passenger numbers and load weights shall by no means exceed specified capacities. Refer to the T
Specifications section of this manual to determine passenger numbers and load weights for your boat. Overweight
will cause overturn and drowning.
7. Inflate according the numbered air chamber and rated pressure on the boat, or it will cause overinflation and boat
explosion. Exceeding the data given on the capacity plate may cause the craft to damage, overturn and lead to
drowning.
8. Keep the boat balanced. Uneven distribution of persons or load in the boat may cause overturn the boat and
drowning.
9. When the boat is in motion, all passengers must remain seated at all times to avoid going overboard.
10. Use the boat in protected shore-zones, up to 300 m (984 feet). Be careful with natural factors such as wind,
tidewaters and tidal waves. BE A
1
puncture the boat.
12. If one chamber is punctured when the boat is in the water
to prevent the boat from sinking.
13. T
14. Don’t leave the boat exposed to sun for long periods of time, as high temperatures shall give rise to air expansion,
which can cause irreparable damage.
15.
16. It is the responsibility of the owner/operator to have at least on bucket/bailer on board, secured against accidental
loss.
17. Never transport the boat in inflated condition on the car
battery acid, oil, petrol. The liquids may damage your boat.
18. Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of others.
19. Follow these instructions to avoid drowning, paralysis or other serious injuries.
20. Know how to operate a boat. Check in your local area for information and/or training as needed. Inform yourself
about local regulations and dangers related to boating and/or other water activities.
SA
Assembling of the boat
NEVER USE HIGH PRESSURE AIR T
YOUR W
1. Spread out the boat on level ground.
2.
back end of the boat.
NOTE: Assemble the fin before inflation and also disassemble it after deflation.
NOTE: T
3
W
data given on the builder’s plate.
T
OWNER’S MANUAL
• Inflate the air chambers with a HAND air pump.
An inflation scale is provided with the product.
Inflate the product until the printed scale is charged up to the same level as that of the supplied scale. (refer the
belowing T
Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the pressure of the boat
each time before using. If you use other pressure gauge, the boat pressure should not be more than the data given on
the builder’s plate.
• Never stand on or rest objects on the boat during inflation.
• Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.
• Extended exposure to sun can shorten the lifespan of your boat. We suggest not leaving boats in direct sunlight for
more than 1 hour after use.
5. Fold the boat from front to back to remove additional air
any remaining air
Repair
1. If there is a small puncture, repair it according to the instruction on repair patch.
2. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or
send the boat to a speciality shop to make the repair
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit
bestwaycorp.com/support to obtain your Certificate of Origin, or you can send e-mail to service@bestwaycorp.us for the
Certificate of Origin.
The HIN is located on the starboard outboard side of the hull and near the stern.
PLEASE KEEP THIS MANUAL IN
SELL THE CRAFT
NOTE: All drawings for illustration purpose only
Storage
1. Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight.
cause damage and shorten the boat’s life span.
4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops together
prevent damage from occurring to the boat inner structures. Next deflate the floor and seat.
Oars Installation
Boat
Components:
• Repair Patch
• Deflation Pipe
Rope x 1
Inflation Scale
Removable Fin x 2
Hand Pump
Elastic Cord x 2
Oar
Oar blade x 2
Shaft x 1
Coupling x 2
Oar ring x 2
Fig. 1
0.03 bar
0.5 psi
Item
65097
Maximum Number of Persons
1 adult
Maximum Load Capacity
150 kg (330 Ibs.)
Inflated Size Recommended
Working Pressure
2.70 m x 1.00 m
(8'10" x 39")
Item
65097 2.70 m x 1.00 m (8'10" x 39") 10 cm 1 1
Product Inflated Size Deflated Size Inflated Size
Chamber 2
Inflated Size
Chamber 1
m
m1112
1112
13
