Bedienungsanleitung Beurer BM49 (Seite 58 von 60) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

651531

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Guidance and manufacture’s declaration – electromagnetic immunity

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and

reﬂection from structures, objects and people.

Field strengths from ﬁxed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile

radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy.

To assess the electromagnetic environment due to ﬁxed RF transmitters, an electromagnetic site survey should be con

sidered. If the measured ﬁeld strength in the location in which the BM49 blood pressure monitor is used exceeds the

applicable RF compliance level above, the BM49 blood pressure monitor should be observed to verify normal opera

tion. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the

BM49 blood pressure monitor.

Over the frequency range 150 kHz to 80 MHz, ﬁeld strengths should be less than 3 V/m.

Recommended separation distances between portable and mobile RF communications equipment and the

EQUIPMENT or SYSTEM – for EQUIPMENT or SYSTEM that are not LIFE-SUPPORTING

Recommended separation distances between portable and mobile RF communications equipment and the BM49

blood pressure monitor

The BM49 blood pressure monitor is intended for use in an electromagnetic environment in which radiated RF distur-

bances are controlled. The customer or the user of the BM49 blood pressure monitor can help prevent electromagnetic

interference by maintaining a minimum distance between portable and mobile RF communications equipment (trans

mitters) and the BM49 blood pressure monitor as recommended below, according to the maximum output power of the

communications equipment.

Rated maximum output

power of transmitter

(W)

Separation distance according to frequency of transmitter

(m)

150 kHz to 80 MHz

d =

80 MHz to 800 MHz

d =

800 MHz to 2.5 GHz

d =

0.01 0.117 0.117 0.234

0.1 0.370 0.370 0.740

1 1.170 1.170 2.340

10 3.700 3.700 7.40 0

100 11.7 11.7 23.4

For transmitters rated at a maximum output power not listed above, the recommended separation distance d in

metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maxi

mum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and

reﬂection from structures, objects and people.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer BM49 Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info