Bedienungsanleitung Beurer JIH50 (Seite 75 von 76) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

533571

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Electromagnetic Compatibility Information

Table 1

For all ME EQUIPMENT and ME SYSTEMS

Guidance and manufacturer’s declaration – electromagnetic emissions

The JIH 50 is intended for use in the electromagnetic environment speciﬁed below.

The customer or the user of the JIH 50 should assure that it is used in such an environment.

Emissions Compliance Electromagnetic environment – guidance

RF emissions CISPR 11 Group 1 The JIH 50 uses RF energy only for its internal function. Therefore, its RF emissi-

ons are very low and are not likely to cause any interference in nearby electronic

equipment.

RF emissions CISPR 11 Class B The JIH 50 is suitable for use in all establishments, including domestic establish-

ments and those directly connected to the public low-voltage power supply net-

work that supplies buildings used for domestic purposes.

Harmonic emissions IEC 61000-3-2 Class C

Voltage ﬂuctuations/ﬂicker emissions

IEC 61000-3-3

Complies

Table 2

For all ME EQUIPMENT and ME SYSTEMS

Guidance and manufacturer’s declaration – electromagnetic immunity

The JIH 50 is intended for use in the electromagnetic environment speciﬁed below.

The customer or the user of the JIH 50 should assure that it is used in such an environment.

Immunity test EN 60601 test level Compliance level Electromagnetic environment – guidance

Electrostatic discharge (ESD)

IEC 61000-4-2

± 6 kV contact

± 8 kV air

± 6 kV contact

± 8 kV air

Floors should be wood, concrete or cera-

mic tile. If ﬂoors are covered with synthetic

material, the relative humidity should be at

least 30 %.

Electrical fast transient/burst

IEC 61000-4-4

± 2 kV for power supply lines ± 2 kV for power supply lines

Mains power quality should be that of a typi-

cal commercial or hospital environment.

Surge

IEC 61000-4-5

± 1 kV line(s) and neutral ± 1 kV line(s) and neutral

Mains power quality should be that of a typi-

cal commercial or hospital environment.

Voltage dips, short interrup-

tions and voltage variations

on power supply input lines

IEC 61000-4-11

<5 % U

(>95 % dip in U

)

for 0.5 cycle

40 % U

(60 % dip in U

)

for 5 cycles

70 % U

(30 % dip in U

)

for 25 cycles

<5 % U

(>95 % dip in U

)

for 5 s

<5 % U

(>95 % dip in U

)

for 0.5 cycle

40 % U

(60 % dip in U

)

for 5 cycles

70 % U

(30 % dip in U

)

for 25 cycles

<5 % U

(>95 % dip in U

)

for 5 s

Mains power quality should be that of a typi-

cal commercial or hospital environment. If

the user of the JIH 50 requires continued

operation during power mains interruptions,

it is recommended that the JIH 50 be pow-

ered from an uninterruptible power supply

or a battery.

Power frequency

(50/60 Hz)

magnetic ﬁeld

IEC 61000-4-8

3 A/m Not applicable Not applicable

NOTE: U

is the a.c. mains voltage prior to application of the test level.

Table 3

For ME EQUIPMENT and ME SYSTEMS that are not LIFE-SUPPORTING

Guidance and manufacturer’s declaration – electromagnetic immunity

The JIH 50 is intended for use in the electromagnetic environment speciﬁed below.

The customer or the user of the JIH 50 should assure that it is used in such an environment.

Immunity test IEC 60601

test level

Compliance

level

Electromagnetic environment – guidance

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

3 V

rms

150 kHz to

80 MHz

3 V/m

80 MHz to

2,5 GHz

3 V

rms

3 V/m

Portable and mobile RF communications equipment should be used no closer to any part

of the JIH 50, including cables, than the recommended separation distance calculated

from the equation applicable to the frequency of the transmitter.

Recommended separation distance:

d = 1,2

d = 1,2 80 MHz to 800 MHz

d = 2,3

800 MHz to 2,5 GHz

Where P is the maximum output power rating of the transmitter in watts (W) according to the

transmitter manufacturer and d is the recommended separation distance in metres (m).

Field strengths from ﬁxed RF transmitters, as determined by an electromagnetic site survey,

should be less than the compliance level in each frequency range.

Interference may occur in the vicinity of equipment marked with the following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is aected by absorption and reﬂection from

structures, objects and people.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Beurer JIH50 Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Beurer JIH50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info