Bedienungsanleitung Binatone BabySense 5 (Seite 1 von 2) (Englisch)

567791

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Breathing & Movement Monitor

Medically approved

Sensor | Do not use | Sensor

Slot

Illustration 6

Sensor | Do not use | Sensor

Hanging hook

Blue breathing

movement

indicator light

Red alert

alarm light

Low battery

warning light

On/Off

button

Illustration 8

Speaker

Control

Unit

Cable Cable

Bed/Crib

base

Control unit holder

Illustration 5

Ensure you read this user guide before installing and

using the product.

Babysense is a high quality, high sensitivity electronic

device which must be handled with care:

• Do not handle roughly, drop or throw.

• Follow the installation instructions carefully to

ensure that it is installed securely and correctly.

• Babysense is not a toy. Do not allow children of any

age to play with it.

• Do not put any additional baby or pet in the bed.

Babysense cannot be used for two infants in one bed.

• You must undertake the performance test daily of

the Babysense monitor (as set out on page 3).

• Do not operate a vaporiser or ventilator directly

towards the bed.

• To avoid possible danger from sensor cords,

ensure that excess cords are pulled back under

the mattress, secured with the included cable tie

and are not visible or reachable.

• Install 4 new and identical size AA 1.5 volt batteries,

preferably alkaline.

• IMPORTANT: It is strongly advised that every

caregiver learn how to give ﬁrst aid.

"Babysense" monitors and alerts, but cannot prevent

cessation of breathing. The responsibility for applying ﬁrst

aid rests on caretakers. The "Babysense" senses breathing

movements and motion only, and cannot monitor

other occurrences. The purpose of the device is to alert

when stopping or slowing of breathing and

movement occur.

"Babysense" is a unique safety system which has helped

save infants, giving parents (or caretaker) assurance,

by enabling intervention in the event of irregular

breathing movement or distress, before it becomes

critical. There are a number of cautionary steps

which are internationally recommended for SAFE

SLEEPING:

* Always lay your baby to sleep on his or her back.

* Refrain from smoking near or around your baby.

* Avoid over-heating the baby's surroundings.

* Do not leave any objects near your baby that can

cause suffocation.

Babysense is an addition to these precautions.

"Babysense" is a home breathing movement monitor

for basically healthy infants up to one year of age,

and is not to be relied on for use with high-risk infants

requiring constant medical supervision.

"Babysense" continually detects the baby's motion and

breathing movements, and will set off a sound and

visual alarm if movement stops for 20 seconds or if the

breathing rate slows to below 10 breaths per minute if

the baby's breathing. The system's non-touch sensor

pads under the mattress monitor baby's movement

without restraining him.

1. Insert, in accordance with the markings, 4 new and

identical size AA 1.5 volt batteries, preferable alkaline.

Close the battery cover.

Note: Do not mix old and new batteries.

Note: For replacing the batteries, remove the battery

cover by inserting a ﬂat screwdriver into the opening

recess (see illustration 7).

Note: Please dispose of used batteries in accordance

with local waste regulations.

2. Place control unit holder on the base of the crib

or bed and in between two bars as shown in

illustration 1.

3. Make sure the sensitivity adjustor, located on the back

of the sensor pads, is positioned on level 3

(see illustration 2).

4. Sensor pad installation:

• When using for an infant not yet able to crawl, place

one sensor pad as shown in illustration 3. Make sure the

sensor is placed underneath the baby's position in the crib.

Warnings

Principal Of Operation

Installation

Please note

9. Place mattress ﬁrmly on top of sensor pads. If the

mattress cannot be in contact with the sensor pads,

or if the bed base is soft, padded or contains

springs, place extra plywood on the bed base, place

the sensor pads on the plywood and place the

mattress ﬁrmly on top.

IMPORTANT: To avoid possible danger from sensor

cords, ensure that excess cords are pulled back

under the mattress, secured with the included cable

tie and are not visible or reachable.

See illustration 8 for layout of control unit featuring:

• On/Off button.

• Blue breathing movement indicator light.

• Acoustic and visual red alarm light.

• Low battery red warning light.

"Babysense" is ready for operation and use once

the installation is complete. To operate, follow the

below instructions:

• Place your baby in the crib/bed.

• Turn control unit on by pressing On/Off button.

• Red control lights switch on brieﬂy and a double

click sound is heard.

• When breathing and movement is sensed, the

blue light ﬂashes.

• Acoustic any visual red light alarms are activated

if the baby's breathing stops or slows signiﬁcantly.

• If the red low-battery warning light ﬂashes,

replace all batteries as soon as possible. If in

addition clicking is heard, all batteries must be

replaced immediately.

• Turn off by pressing On/Off button before taking

your baby out of the crib/bed.

User Guide

Illustration 2

• When the baby begins to crawl, and is able to move

onto areas not "covered" by a single sensor pad, attach

the second sensor and place the two sensors as shown

in illustration 3.

PLEASE NOTE: The sensors shall be placed with the

marking “THIS SIDE UP” facing upfront.

5. Pass the cord(s) of the sensor pad(s) through

special openings in the holder. (see illustration 4)

6. Attach end(s) of the cord(s) to the outlets

marked "SENSOR" on the back of control unit

(see illustration 5 and 6). When using one sensor

pad, attach to either “SENSOR” outlet.

PLEASE NOTE: Do not attach any cable to the

blocked socket, marked "DO NOT USE"

7. Should the design of the crib/bed not allow proper

installation with the control unit holder, please use the

optional hanging hook (see illustration 6) and hang the

control unit from the bottom edge of the crib.

8. Press control unit holder or hanging hook ﬁrmly

into slot in back of control unit (see illustration 5 and 6).

"Babysense" is a highly sensitive device which

monitors baby's breathing movements through the

mattress during sleep. There are two main causes of

malfunction - technical malfunctions and

malfunctions due to environmental factors.

In order to minimise technical problems, follow

installation and operation instructions carefully.

Due to the high sensitivity of "Babysense", it can

be influenced by fans, wind, air conditioning, and

so forth. Such environmental effects could be

picked up by the sensors on a similar level to that of

breathing movements, thus preventing or delaying

alarm activation.

Do not conduct performance test by picking up

baby out of bed and waiting for the alarm to sound

• The performance test should be conducted

while the baby is not in bed.

• Turn device on and take two steps back from bed.

• Ensure the alarm goes off within 20 seconds

(due to absence of breathing movements).

• The alarm may sound with or without

preliminary ticking.

• Check the alarm can be heard in all locations

throughout the home or place of care.

• In case the alarm does not sound within 20

seconds refer to troubleshooting at page 5.

• The performance test must be conducted daily.

Isolated cases of false alarms are possible. Check if caused

by faulty connection of the sensor pad(s) to the control

unit, connection of only one sensor pad when the baby

can move off the immediate area, connection of two

sensor pads far apart from each other when the baby is

not crawling yet, or failure of the sensor pads to be

directly against the mattress.

In case of false alarms, kindly refer to troubleshooting

guide. If the problem cannot be solved, please

contact your nearest BABYSENSE representative.

Act immediately according to the following:

1. Approach the bed and check that baby is breathing.

Note pallor (color of skin), muscle tone and movement.

2. If baby does not seem normal, pinch baby's heel

and check that there is no cause for choking,

such as an object lodged in baby’s throat.

When breathing resumes, consult a doctor.

3. If breathing does not resume, apply first aid and seek

medical assistance immediately.

Sensor | Do not use | Sensor

Slot

Battery

cover

Blocked socket

DO NOT USE

“Sensor”

socket

Illustration 7

Opening

recess

Speaker

Layout of control unit

Operation

Testing Operation

Technical malfunction

Environmentally caused malfunction

Conduct this performance test daily

False alarms

In the event of alarm

Cables

Illustration 4

Control unit

holder

Illustration 1

Control unit holder

Cables

Sensor

Sensor pads

(Under mattress)

Control unit

Illustration 3

Top crib/bed view

For babies not

yet able to crawl

For crawling babies

Top crib/bed view

Binatone BabySense 5 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info