Bedienungsanleitung Black Decker ADE80 (Seite 2 von 7) (Englisch)

53548

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

ENGLISH

en - 2

Description (fig. A1 & 2)

Your Elu Surfacing/Thicknessing attachment ADE80 (Type 3) has been

designed to extend the versatility of your MFF80/MFF81 or HH40/HH40E

planer by converting it into a compact planer/thicknesser.

1 Switch strap

1a Switch wedge for use with HH40 models

2 Securing clip

3 Wing nuts

4 Bench clamp holes

5 Thicknessing adjuster

6 Aluminium frame

7 Thicknessing table

8 Table height adjuster

9 Thicknessing scale

10 Surfacing adjuster

11 Planing depth adjuster

12 Blade guard for thicknessing

13 Reversible fence

14 Thicknessing table clamp

15 Fence securing knobs

16 Rear support foot

17 Support bracket with foot

18 Planer mounting rods

No-volt release switch

A no-volt release switch is available as an option (E38676). It offers the

following advantages:

- Optimum safety: It prevents the machine from restarting inadvertantly in

the event of a power loss.

- It allows easier switching of the planer.

Assembly and adjustment

Do not mount any Power Tools other than the MFF80/MFF81

or HH40/HH40E.

Assembling the attachment (fig. A & B)

The screws and nuts required to assemble the attachment are supplied

with the surfacing/thicknessing attachment.

• Slacken the thicknessing table clamp (14).

• Raise the thicknessing table (7) by rotating the table height adjuster (8).

• Mount the rear support foot (16), the arm (28) and support bracket with

foot (17) using the nuts and screws (21 through 27) as shown.

Mounting the planer (fig. C)

• Remove the wing nuts (3) and the securing clip (2).

• Hinge the planer mounting rods (18) up and mount the planer as

shown.

• Reinstall the wing nuts (3).

• Pivot the planer into surfacing or thicknessing position and tighten the

wing nuts (3).

• Fit the securing clip (2) in the appropriate groove of the rear mounting

rod.

Calibration (fig. A & D)

The calibration procedure needs to be performed only once.

• Remove the calibration fence (20) and place it on the thicknessing table (7),

gauge cams (29) up.

• Set the table height to 15 mm using the table height adjuster (8).

• Secure the adjustment using the thicknessing table clamp (14).

• Pivot the planer into thicknessing position and check that all four gauge

cams (29) are level against the planing shoe. Adjust as required.

• Tighten the wing nuts (3).

• Loosen the thicknessing table clamp (14) and lower the thicknessing

table (7).

• Remove the calibration fence and reinstall it in its original position as a

side guard.

Adjusting the planing depth

• For planing depth adjustment, refer to the instruction manual of the

planer.

• Make shallow cuts only, passing the material several times if required.

For optimal results, select a maximum planing depth of 1.5 mm.

Thicknessing position (fig. A & E)

• Remove the reversible parallel fence (13) by loosening the star knobs (15).

• Swivel the support bracket (17) aside or remove it and pivot the planer

into thicknessing position. The planer mounting rods (18) now rest in

the brackets (30).

Thicknessing table height adjustment (fig. A)

• Loosen the thicknessing table clamp (14).

• Raise or lower the table by rotating the table height adjustment screw (19).

• Tighten the thicknessing table clamp (14).

Surfacing position (fig. B & F)

• Remove the calibration fence.

• Loosen the thicknessing table clamp (14).

• Set the thicknessing table (7) to bottom position.

• Swivel the blade guard (12) aside and pivot the planer into surfacing position.

The planer mounting rod (18) now rests in the support bracket (17).

• Check that the rear of the planer rests on the arm (28 in fig. B).

• If required, loosen the screw (26) using a screwdriver.

• Adjust the arm (28 in fig. B) in its slot and secure the screw.

• Tighten wing nut (3) to lock the planer in surfacing position.

Mounting the reversible parallel fence (fig. A2)

• Lower the side guard of the planer and install the reversible parallel

fence (13).

• Tighten the star knobs (15).

• For 45° bevelled workpieces, remove the star knobs (15), reverse the

fence, refit the star knobs and level the fence on the planer shoe.

Adjusting the blade guard (fig. G)

The blade guard (12) is mounted on a support bracket (17) that can be

pivoted away when the planer is not in surfacing position. In surfacing

position, the bracket also serves as a support to the planer mounting rod.

The blade guard height is adjustable.

• Loosen the surfacing adjuster (10), adjust the blade guard height in the

slot (31) and tighten the screw.

Adjusting the planer in surfacing position to be 90° to the reversible

fence (fig. C & G)

The calibration procedure needs to be performed only once.

• Use a square to check that the angle is 90°.

If this is not the case:

• Remove the reversible fence (13).

• Loosen the wing nuts (3).

• Pivot guard (12) away.

• Pivot the planer up.

• Adjust the height adjustment screw (19) accordingly.

Dust extraction

• Use the dust extraction adapter of your planer and install it as

described in the instruction manual of the planer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker ADE80 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info