Bedienungsanleitung Black Decker AST6XC (Seite 6 von 8) (Englisch)

53567

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Fitting the side handle

◆ Screw the side handle (2) into one of the mounting holes

in the tool.

Warning! Always use the side handle.

Fitting and removing grinding or cutting discs (fig. C - E)

Always use the correct type of disc for your application.

Always use discs with the correct diameter and bore size

(see technical data).

Fitting

◆ Fit the guard as described above.

◆ Place the inner flange (10) onto the spindle (5) as shown

(fig. C). Make sure that the flange is correctly located on

the flat sides of the spindle.

◆ Place the disc (11) onto the spindle (5) as shown (fig. C).

If the disc has a raised centre (12), make sure that the

raised centre faces the inner flange.

◆ Make sure that the disc locates correctly on the inner flange.

◆ Place the outer flange (13) onto the spindle. When fitting

a grinding disc, the raised centre on the outer flange must

face towards the disc (A in fig. D). When fitting a cutting

disc, the raised centre on the outer flange must face away

from the disc (B in fig. D).

◆ Keep the spindle lock (3) depressed and tighten the outer

flange using the two-pin spanner (14) (fig. E).

Removing

◆ Keep the spindle lock (3) depressed and loosen the outer

flange (13) using the two-pin spanner (14) (fig. E).

◆ Remove the outer flange (13) and the disc (11).

Fitting and removing sanding discs (fig. E & F)

For sanding, a backing pad is required. The backing pad is

available from your Black & Decker dealer as an accessory.

Fitting

◆ Place the inner flange (10) onto the spindle (5) as shown

(fig. F). Make sure that the flange is correctly located on

the flat sides of the spindle.

◆ Place the backing pad (15) onto the spindle.

◆ Place the sanding disc (16) onto the backing pad.

◆ Place the outer flange (13) onto the spindle with the

raised centre facing away from the disc.

◆ Keep the spindle lock (3) depressed and tighten the outer

flange using the two-pin spanner (14) (fig. E). Make sure

that the outer flange is fitted correctly and that the disc is

clamped tightly.

Removing

◆ Keep the spindle lock (3) depressed and loosen the outer

flange (13) using the two-pin spanner (14) (fig. E).

◆ Remove the outer flange (13), the sanding disc (16) and

the backing pad (15).

Use

Warning! Let the tool work at its own pace. Do not overload.

◆ Carefully guide the cable in order to avoid accidentally

cutting it.

◆ Be prepared for a stream of sparks when the grinding or

cutting disc touches the workpiece.

◆ Always position the tool in such a way that the guard

provides optimum protection from the grinding or cutting

disc.

Switching on and off

◆ To switch on, slide the on/off switch (1) forward. Note that

the tool will continue running when you release the switch.

◆ To switch off, press the rear part of the on/off switch.

Warning! Do not switch the tool off while under load.

Hints for optimum use

◆ Firmly hold the tool with one hand around the side handle

and the other hand around the main handle.

◆ When grinding, always maintain an angle of approx. 15°

between the disc and the workpiece surface.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Warning! Before performing any maintenance, switch off and

unplug the tool.

◆ Regularly clean the ventilation slots in your tool using

a soft brush or dry cloth.

◆ Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

◆ Safely dispose of the old plug.

◆ Connect the brown lead to the live terminal in the new plug.

◆ Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality

plugs. Recommended fuse: 5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker AST6XC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info