Bedienungsanleitung Black Decker AST8XC (Seite 5 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

53571

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ENGLISH

different from those intended could result in a hazardous

situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will make sure that the safety of the power tool is

maintained.

Specific safety instructions for jigsaws

X Hold the tool by the insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a "live" wire will make exposed metal parts of

the tool "live" and shock the operator.

X Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

X Keep hands away from cutting area. Never reach

underneath the work piece for any reason. Do not insert

fingers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

X Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

X When cutting pipe or conduit, make sure that they

are free from water, electrical wiring, etc.

X Do not touch the workpiece or the blade

immediately after operating the tool. They can become

very hot.

X Be aware of hidden hazards, before cutting into

walls, floors or ceilings, check for the location of

wiring and pipes.

X The blade will continue to move after releasing the

switch. Always switch the tool off and wait for the saw

blade to come to a complete standstill before putting the

tool down.

This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised to

ensure they do not play with the appliance.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specifically

designed for protection against dust and fumes and ensure that

persons within or entering the work area are also protected.

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

X If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker service

centre in order to avoid a hazard.

Features

This tool includes some or all of the following features:

1. Variable speed On/off switch

2. Lock-on button

3. Dust extraction outlet

4. Shoe plate

5. Saw blade support roller

6. Pendulum stroke selector

Fig. E

7. Saw blade storage compartment (KS702PE & KS703PE)

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped. Used saw blades may be hot.

Adjusting the saw blade support roller (fig. A & B)

X Loosen the two screws (9).

X Push the saw blade support roller (5) forward until it

touches the back edge of the saw blade (8).

X Tighten the two screws (9).

Fitting and removing the saw blade (fig. C)

Before fitting or removing the saw blade (8) the saw blade

support roller (5) must be adjusted to the rear position so that

it does not contact the blade.

X Loosen (do not remove) the two screws (11).

X Hold the saw blade (8) with the teeth facing forward.

X Insert the shank of the saw blade (8) into the blade holder

(10) as far as it will go.

X Slightly tighten the two screws (11) alternately to position

the blade, then fully tighten the two screws (11).

X Adjust the saw blade support roller (5) as described above.

X To remove the saw blade (8), turn both screws (11) one turn

counter-clockwise.

Connecting a vacuum cleaner to the tool (fig. D)

An adaptor (12) is required to connect a vacuum cleaner or

dust extractor to the tool. The adaptor can be purchased from

your local Black & Decker retailer.

X Push the adaptor (12) into the dust extraction outlet (3).

X Connect the vacuum cleaner hose (13) to the adaptor (12)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker AST8XC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker AST8XC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info