Bedienungsanleitung Black Decker BDJS350 T1 (Seite 5 von 12) (Englisch)

581315

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Electrical safety

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Warning! Never attempt to replace the charger unit with a

regular mains plug.

Features

This appliance includes some or all of the following features:

1. LED area light

2. Heavy-duty copper clamps

3. LED area light on/off switch

4. Reverse polarity indicator

5. Jumper cables

6. Mains charging adaptor

7. ON/OFF switch

8. Carry handle

9. Battery status pushbutton

10. Battery status LEDs

11. 12 Vdc charging socket

12. Clamp holders

USE

Charging the unit (fig. A)

This unit is shipped in a partially charged state.

 Charge the unit before first use using the mains

charging adaptor (6) for 48 hours.

Lead-acid batteries require routine maintenance to ensure a

full charge and a long battery life. All batteries lose energy

from self-discharge over time and more rapidly at higher

temperatures. When the unit is not in use, Black & Decker

recommend that the battery is charged at least every 60

days.

 Check the battery charge level by pressing the battery

status pushbutton (9). The LED charge status display

(10) will indicate the level of battery charge. When only

one red LED lights, charge the unit.

Note: Charging the battery after each use will prolong the

battery life; frequent heavy discharges between charges

and/or overcharging will reduce battery life.

The battery can be charged using the mains charging

adaptor (6).

Charging the unit with the mains charger (fig. C)

Make sure that the ON/OFF switch (7) and the LED area light

(1) are turned off while the unit is being charged.

 Insert the jack plug of the charging adaptor (6) into the

charging socket (11).

 Insert the charging adaptor (6) into a mains power

socket.

As charging progresses, the red LEDs will light one by one.

 Charge the unit until the green FULL LED lights/flashes.

 Continue to charge for one to two more hours.

Note: The mains charging should not be connected for more

than 60 hours.

 When charging is complete remove the charging

adaptor (6) form the mains power socket.

 Remove the charging jack plug from the charging

socket (11) and store in a safe place.

Using the unit as a jump-starter (fig. A & B)

Warning! Make sure that the vehicle is in neutral with the

parking brake applied.

Note: If your connections are incorrectly made, the unit will

beep continuously and the red reverse polarity indicator (4)

will illuminate, even if the ON/OFF switch (7) is in the OFF

position. Rectify the connections immediately.

Warning! Make sure that the cables are not in the path of

moving belts or the fan.

1. Turn off the vehicles ignition and all accessories before

making any connections.

2. Make sure that the units ON/OFF switch (7) is turned

OFF.

3. The following procedure is for a negative earth system

ie the negative battery terminal is connected to the

chassis.

4. Connect the positive (+) red clamp to the vehicle's

positive battery terminal.

5. Connect the negative (-) black clamp to chassis or a

solid, non-moving, metal vehicle component or chassis

part. Never clamp directly to negative battery terminal or

moving part. Refer to the automobile owner’s manual.

6. Turn the unit’s ON/OFF switch (7) to the ON position.

7. Start the vehicle and crank the engine in 3 to 6 second

bursts.

 If the engine doesn’t start within 6 seconds let the units

internal battery cool for 3 minutes before making

another attempt.

8. When the vehicle starts, turn the unit’s OFF/ON switch

(7) to the OFF position.

9. Leave the vehicle’s engine running.

10. Disconnect the (-) black clamp connected to the engine

or chassis first, followed by the (+) red clamp that is

connected to the battery positive (+) terminal.

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDJS350 T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDJS350 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info