Bedienungsanleitung Black Decker BDL500M T1 (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578007

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

Fig. A

7. On/off switch (measurer)

8. Set key

9. Repeat measurement key

10. Spacing key

11. Reset key

Fig. B

12. Wallpin

13. Keyhole wall mount

Assembly

Fitting the battery (fig. C)

◆ Remove the battery cover (14) from the tool.

◆ Insert the batteries into the tool in the orientation as shown.

◆ Refit the cover and let it click into place.

Wall mounting (fig. B & D)

The tool can be mounted to walls using one of the wall

mounts (12 or 13).

Wall pin

If the tool is mounted to drywall or other soft materials, the

wall pin (12) must be used. The position of the laser line will

line up with the mounting location of the pin.

◆ Remove the protective cap (15) from the pin (16) and store

it on the insert as shown (fig. D).

◆ Hold the wall pin at the required height in front of a

suitable location and press the pin straight into the wall.

◆ Install the tool by hanging the holder (4) on the wall mount.

Warning! The pin of the insert is sharp and should be

handled with care. Replace the protective cap immediately

after removing the insert from the wall.

Keyhole wall mount

For surfaces other than drywall, the keyhole wall mount (13)

can be used with a screw in a predrilled hole. The position of

the laser line will line up with the mounting location of the screw.

◆ Hang the wall mount on a screw mounted at the required

height on a suitable location.

◆ Install the tool by hanging the holder (4) on the wall

mount.

Use

Using the laser level function (fig. E & F)

Using the laser in auto-leveling mode

◆ Hang the tool on the wall using the appropriate wall mount.

◆ Push the on/off switch (1) up to switch the tool on in auto-

leveling mode.

The auto levelling indicator (17) will light up and swing while

the tool is calibrating.

Note: the laser lines will only be level if the tool is kept within

5° from vertical.

◆ Push the on/off switch (1) down to switch the tool off.

Using the laser in locked/layout mode

When operating in the locked/layout mode, the tool can be

held in horizontal position, for surface layout such as flooring

and tiling.

◆ Place the tool flat on the floor.

◆ Push the on/off switch (1) down to switch the tool on in

locked/layout mode. The locked/layout indicator (18) will

light up.

◆ Move the tool as necessary to position the laser lines.

◆ Push the on/off switch (1) up to switch the tool off.

Using the measurer function

Switching on and off (fig. A)

◆ To switch the tool on, press key (7).

◆ To switch the tool off, press key (7) again.

Setting the reference point (fig. A, E & G)

The reference point is the part of the tool that the measurement

starts from and ends at. The reference point can be aligned

with the left (19), the right (20) or the centre (21) of the tool.

For accurate results, the reference point can be set before and

after the measurement.

◆ To set the reference point, press either of keys (8).

Selecting the measurement system (fig. A & E)

The appliance can show the results both in the metric (22) and

the imperial system (23).

◆ To switch from one measurement system to the other,

press and hold key (7) for 4 seconds.

Measuring (fig. A & E)

◆ Place the tool flat against the wall at the start of the

distance to be measured. Switch the tool on.

◆ Press and hold key (11) for 4 seconds. The ready-for-use

indicator (24) will light up.

◆ Set the reference point indicating the start of the

measurement.

◆ Slowly slide the tool along the distance to be measured.

Make sure not to tilt or lift the tool.

◆ Set the reference point indicating the end of the

measurement.

◆ To reset the tool, press and hold key (11) for 4 seconds.

Wait for the ready-for-use indicator (24) to light up before

continuing.

Note: After 2 minutes of inactivity the LCD screen will go blank.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDL500M T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker BDL500M T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info