Bedienungsanleitung Black Decker BDSBC10A (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

53631

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

For estimates of the time it takes to charge a battery, refer to

the following table:

The times shown in the table above are approximate and are

based on a 50% discharged battery. The battery charging

times will vary depending on the size, age and condition of

the battery.

Alternator check (fig. B)

A faulty alternator can be the hidden cause of a discharged

battery.

Warning! Check only 12 Vdc systems.

Part 1 (no load)

X Make sure that there is no load on the alternator by

turning off all the vehicles accessories.

X The battery must be fully charged before testing the

alternator.

X Run the engine for 3 minutes to achieve normal idle

speed and verify that there is a no-load voltage.

X Using the function control knob (3), select alternator

check (fig. C) before connecting the clamps to the

battery, ANALYSING ALTERNATOR will be displayed

after the clamps are connected.

X When the unit has completed checking, ALTERNATOR

GOOD will be displayed and the green LED will light to

indicate that the alternator is good or ALTERNATOR

BAD or ENGINE NOT RUNNING and the red LED will

light to indicate that the alternator is out of typical

voltage range.

Part 2 (under load)

X Load the alternator by turning on as many accessories

as possible except for air-conditioning and defrost.

X Once the unit has completed checking, ALTERNATOR

GOOD will be displayed and the green LED will light to

indicate that the alternator is good or ALTERNATOR

BAD or ENGINE NOT RUNNING and the red LED will

light to indicate that the alternator is out of typical

voltage range.

If the first alternator check indicates a good alternator and

the second indicates the alternator is not good, the problem

could be caused by any of the following:

X Loose fan belts.

X An intermittent diode failure.

X Bad connections between the battery and alternator

and/or ground.

Note: ALTERNATOR BAD or ENGINE NOT RUNNING may

be displayed if a number of extra accessory loads have been

added to the charging system, thereby increasing current

demand from the alternator. Make sure that the alternator is

rated to support the application.

Troubleshooting

Display indications, common problems and possible

solutions:

No Functions

X Make sure that the battery charger is plugged into a live

230 Vac outlet.

X Follow the steps outlined in the “Connecting the battery

charger” at the front of this manual.

X The unit will turn on automatically after being properly

connected to the battery. If it does not come on, either it

is not connected properly to the terminals or the voltage

of the battery to be serviced is too low (below 3.0 Volts).

Smart charge fault condition messages

CHECK BATTERY CONNECTIONS - When this message

appears, the most common cause is a poor connection to

the battery.

X Observing the “Safety instructions” at the front of this

manual, disconnect mains cord and the battery

clamps (4), clean the battery terminals and reconnect. If

the situation persists, we recommend taking your

battery to a certified automotive service centre for

evaluation.

REPLACE OR SERVICE BATTERY - The battery being

charged either has an internal open circuit, a shorted cell or

is highly sulphated and cannot accept a normal charge

current. We recommend taking your battery to a certified

automotive service centre for evaluation.

COOL DOWN CYCLE - red LED lit -The ventilation grill that

allows the air from flowing in and out of the charger may be

blocked.

X Make sure there is ample ventilation before resuming

operation.

REVERSE CLAMPS ON TERMINALS - The red LED lights

and a continuous warning tone sounds.

The connections to the battery’s positive and negative

terminals are incorrect.

X Observing the “Safety instructions” at the front of this

manual, disconnect the mains cord and the battery

clamps (4) and reconnect the clamps as described in

the section “Charging the battery”.

OVERTIME CONDITION - When this message is displayed,

the charging cycle has exceeded 18 hours; this condition

may occur because of the following:

20Ah 60Ah 180Ah 360Ah 450Ah 560Ah

10A 1.06hr

3.20hr

10.00hr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BDSBC10A Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info