Bedienungsanleitung Black Decker CS355 T1 (Seite 8 von 12) (Englisch)

579640

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

ENGLISH

(Original instructions)

Maximum cutting capacity

Note: Capacity shown on chart assumes no wheel wear and

optimum fence position.

Workpiece

shape

cutting

angle

A = 4-7/8"

(125mm)

A = 4-1/2"

(115mm)

4-1/2" x 5-1/8"

(115mm x 130mm)

4" x 7-5/8"

(115mm x 130mm)

3" x 7-3/8"

(115mm x 130mm)

A = 4-1/2" x 5-3/8"

(115mm x 137mm)

Cutting

Angle

A= 4-1/2"

(115mm)

A = 3-13/16"

(98mm)

4-1/2" x 3-13/16"

4-1/8" x 3-3/4"

(105mm x 95mm)

A = 3-13/16"

3-3/4"

(95mm)

Prior to operation:

u Install the appropriate cutting disc. Do not use excessively

worn discs. The maximum rotation speed of the tool must

not exceed that of the cutting disc.

u Make sure the disc rotates in the direction of the arrows

on the accessory and the tool.

u Secure the workpiece.

u Always set the spark deector correctly.

Switching on and off (g. 1)

The on/off trigger switch (N) is mounted in the operating

handle.

u To run the tool, press the on/off trigger switch (N).

u Keep the on/off switch depressed while performing the

operation.

u To stop the tool, release the trigger switch (N).

Warning: Do not switch the tool on or off when under load.

Warning: To prevent unauthorized use of tool, install a

standard padlock (not included) into the padlock hole (O)

located in the trigger switch.

Warning! Do not cut magnesium.

Consult your dealer for further information on the

appropriate accessories.

Performing a cut (g. 1)

u Place the material to be cut against the fence (E) and

secure using the vise (F).

u Switch on the tool and pull down the handle to cut the

workpiece. Allow the motor to reach full speed before

cutting.

u Allow the disc to cut freely. Do not force.

u After completing the cut, switch off the tool and return the

arm to its upper rest position.

Transporting (g. 1)

The tool is equipped with a lock chain (A) which locks the

tool in closed-down position for carrying.

Warning: Ensure that the tool is switched off and

disconnected from the mains supply before transporting.

u Lower the guard (K) onto the cutting table base (D) and

secure the tool in this position by securing the chain on

the hook in the handle.

u Transport the tool using the carrying handles.

u To release the tool, depress the operating handle slightly

and pull off the lock chain (A).

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper appliance/tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless appliance/tool:

u Switch off and remove the battery from the appliance.

u Keep the ventilation slots clear and regularly clean the

housing with a soft cloth.

u Do not use abrasive cleaners.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality

plugs. Recommended fuse: 13 A.

Motor brush inspection and replacement (g. 9)

Warning! Turn off and unplug the tool. Be sure the trigger

switch is in the OFF position.

Brushes should be regularly inspected for wear. To inspect

brushes, remove brush cap (W). Brushes (V) should slide

freely in brush box. If brushes are worn down to .3" (8mm) as

shown in Figure 9 they should be replaced.

To reinstall, push new brush back into brush box. If replacing

existing brush, maintain same orientation as when removed.

Replace the brush cap (do not overtighten).

Cleaning

Blowing dust and grit out of the main housing by means of an

air hose is recommended and may be done as often as dirt is

seen collecting in and around the air vents. Always wear

proper eye and respiratory protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker CS355 T1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker CS355 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info