Bedienungsanleitung Black Decker FSMH1300FX (Seite 7 von 8) (Englisch)

709565

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

u Use water only with no additives or chemicals with your

steam mop. To remove stubborn stains from vinyl or

linoleum oors, you can pre-treat with a mild detergent

and some water before using the steam mop.

Steam Cleaning with the mop

u Fit hand steam cleaner to the oor extension (8)

u Place a cleaning pad (10) on the oor with the velcro 'loop'

side facing up.

u Lightly press the steam mop down onto the cleaning pad

(10).

u Connect the steam mop to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Turn the Autoselect

dial (2) until the required setting is

reached. After a few seconds steam will start to come out

of the steam head.

Note! When rst lled or after running dry, it can take up to 45

seconds for steam to be produced.

u It takes a few seconds for steam to enter the cleaning pad.

The steam mop will now glide easily over the surface to be

sanitized/cleaned.

u Push and pull the steam mop slowly across the surface to

thoroughly steam clean each section.

u When you have nished using the steam mop, return

the handle (8) to the upright position, making sure that it

is supported and turn it 'OFF'. Wait until the steam mop

cools down (approximately ve minutes).

Caution! It is important to monitor the water level in the water

tank. To rell the water tank and continue to sanitize/clean

stand the mop upright making sure that it is supported and

turn the steam mop 'OFF'. Unplug the unit from the electrical

wall outlet, and rell the water tank.

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop

supported in the upright position when stationary and make

sure the steam mop is turned off when not in use.

After use

u Turn the Autoselect

dial (2) to the OFF position.

u Wait until the steam mop cools down.

u Unplug the steam mop from the electrical wall outlet.

u Empty the water tank.

u remove the cleaning pad (10) and wash it ready for next

use (take care to follow the wash care instructions printed

on the cleaning pad).

Accessories

The performance of your appliance depends on the accessory

used. BLACK+DECKER accessories are engineered to high

quality standards and designed to enhance the performance

of your appliance. By using these accessories you will get the

very best from your equipment.

Hand held steam cleaning

Warning! Only use in a horizontal position.

u Attach the required accessory.

u Connect the hand held steam cleaner to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Turn the Autoselect

dial (2) until the required setting is

reached. After a few seconds steam will start to come out

of the steam head.

Note! When rst lled or after running dry, it can take up to 45

seconds for steam to be produced.

u When you have nished using the hand held steam

cleaner turn the Autoselect

dial (2) to the OFF position.

Turn the unit OFF by pressing the ON/OFF button (1) and

disconnect from the mains supply. Wait until the unit cools

down before storing (approximately ve minutes).

Technical Data

FSMH1300FX

Voltage V

230

Power W 1300

Tank

Capacity

ml 500

Weight kg 2.4

Troubleshooting

If your appliance seems not to operate properly, follow the

instructions below. If this does not solve the problem, please

contact your local BLACK+DECKER repair agent.

Problem Step Possible solution

The steam mop is not

turning on

1. Check the unit is plugged in at the wall

socket.

2. Check the unit is switched on using the

ON/OFF switch (1)

3. Check the fuse in the plug.

The steam mop is not

producing steam

4. The steam mop will only produce steam if

the hand held steam cleaner (5) is

correctly docked into the main body (11)

or the steam hose is tted or the

Autoselect

is turned to ON

5. Check that the water tank is full. Note:

When rst lled or after running dry it can

take up to 45 seconds for steam to be

produced.

6. Check steps 1, then 2, then 3

The steam mop stops

producing steam

during use

7. Check steps 4, then 5, then 3

The steam mop is

producing too much

steam during use

8. Turn the Autoselect

dial (2)

anti-clockwise to reduce the amount of

steam being produced

The steam mop is

producing too little

steam during use

9. Turn the Autoselect

dial (2) clockwise to

increase the amount of steam being

produced

Where can I get further

information/

accessories

10. www.blackanddecker.co.uk/steammop

www.blackanddecker.ie/steammop

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker FSMH1300FX Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info