Bedienungsanleitung Black Decker GTC3655PCLB (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

665811

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

(Original instructions)

When the charger detects a battery that is excessively

hot or excessively cold, it automatically starts a Hot/Cold

Pack delay, suspending charging until the battery has

normalised. After this happens, the charger automatically

switches to the Pack Charging mode. This feature ensures

maximum battery life. The red LED ashes in the pattern

indicated on the label when the Hot/Cold pack delay is

detected.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack .

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the appliance, battery

pack and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Shock hazard. Do not allow any liquid to get inside

charger. Never attempt to open the battery pack for any

reason.

If the plastic housing of the battery pack breaks or cracks,

return to a service center for recycling.

State of charge indicator

The battery is equipped with a state of charge indicator. This

can be used to display the current level of charge in the bat-

tery during use and during charging.

It does not indicate tool functionality and is subject to variation

based on product components, temperature and end-user

application.

Checking state of charge during use

u Press the state of charge indicator button (A1).

u The three LEDs (A2) will illuminate, indicating the percent

of charge in the battery. See chart in gure a.

u If LED light does not illuminate, charge battery.

Installing and removing the battery pack from the

appliance

Warning! Make certain the lock-off button is not engaged to

prevent switch actuation before removing or installing battery.

To install battery pack

Insert battery (8) into appliance until an audible click is heard

(Figure B). Ensure battery pack is fully seated and fully

latched into position.

To remove battery pack

Depress the battery release button as shown in Figure C and

pull battery pack out of appliance.

Assembly

Warning! Before assembly, remove the battery from the tool

t the blade sheath over the blades.

Warning! Before assembly, make sure that the tool is

switched off and unplugged and that the blade sheath is tted

over the blades.

Warning! Never use the tool without the guard.

Fitting the guard and bail handle (g. D–F)

Warning! Only use the tool with the guard and handle

properly assembled. Using the hedge trimmer without the

proper guard or handle provided may result in serious injury.

Note: The hedge trimmer was shipped with the guard and bail

handle attached to the hedge trimmer with a plastic tie.

u Cut the plastic tie.

u Remove the partially inserted screws from the body of the

tool (Fig. D).

u Slide the guard (5) onto the front of the hedge trimmer

housing (Fig. E).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GTC3655PCLB Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info