Bedienungsanleitung Black Decker kc 36 (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

381281

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

◆ When disposing of batteries, follow the instructions given

in the section “Protecting the environment”.

◆ Under extreme conditions, battery leakage may occur.

When you notice liquid on the battery, proceed as follows:

- Carefully wipe the liquid off using a cloth. Avoid skin

contact.

- In case of skin or eye contact, follow the instructions below.

Warning! The battery fluid, a 25-30% solution of potassium

hydroxide, can be harmful. In case of skin contact,

immediately rinse with water. Neutralise with a mild acid

such as lemon juice or vinegar. In case of eye contact, rinse

abundantly with clean water for at least 10 minutes. Consult a

physician.

◆ Do not incinerate the battery.

◆ Do not attempt to charge damaged batteries.

Chargers

◆ Use your Black & Decker charger only to charge the battery

in the tool with which it was supplied. Other batteries

could burst, causing personal injury and damage.

◆ Never attempt to charge non-rechargeable batteries.

◆ Have defective cords replaced immediately.

◆ Do not expose the charger to water.

◆ Do not open the charger.

◆ Do not probe the charger.

The charger is intended for indoor use only.

Electrical safety

Your charger is double insulated; therefore no earth

wire is required. Always check that the mains

voltage corresponds to the voltage on the rating

plate. Never attempt to replace the charger unit with

a regular mains plug.

Features

This tool includes some or all of the following features.

1. On/off switch with forward/reverse function

2. Bit holder

3. Charger connector

4. Charger

5. Battery

Assembly

Warning! Make sure that the tool is switched off.

Fitting and removing a screwdriver bit (fig. B)

◆ To fit a screwdriver bit (6), push it into the bit holder (2)

until it locates.

◆ To remove a screwdriver bit, pull it straight from the bit

holder.

Use

Charging the battery (fig. C)

The battery needs to be charged before first use and whenever

it fails to produce sufficient power on jobs that were easily

done before. A new battery or a battery that has not been

used for a long period of time achieves full performance only

after approximately 5 charging and discharging cycles.

After normal use, a charging time of 12 hours will enable the

tool to operate at an effective power level for most tasks.

However, further charging for up to 24 hours could significantly

increase the run time, depending on the battery and charging

conditions. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

◆ To charge the battery, insert the charger plug (7) into the

connector (3).

◆ Plug in the charger. Switch on at the mains.

◆ Leave the tool connected to the charger for at least 12 hours.

The tool can be left connected to the charger indefinitely.

The charger may hum and become warm while charging;

this is normal and does not indicate a problem.

◆ Before using the tool, unplug the charger and disconnect

the tool from the charger.

Warning! Do not use the tool while it is connected to the charger.

Operating the tool (fig. D)

◆ To tighten a screw or nut, slide the on/off switch (1) to

the right and press it.

◆ To loosen a screw or nut, slide the on/off switch (1) to the

left and press it.

◆ To switch the tool off, release the on/off switch.

Hints for optimum use

◆ Always use the correct type and size of screwdriver bit.

◆ If screws are difficult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

◆ Use the spindle lock to loosen very tight screws or to

firmly tighten screws.

◆ Always hold the tool and screwdriver bit in a straight line

with the screw.

◆ When screwing in wood, it is recommended to drill a pilot

hole with a depth equal to the length of the screw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker kc 36 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info