Bedienungsanleitung Black Decker KD976KA T3 (Seite 7 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

602312

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

ENGLISH

Fittingthesidehandleanddepthstop(g.A)

u Turn the grip counterclockwise until you can slide the side

handle (7) onto the front of the tool as shown.

u Rotate the side handle into the desired position.

u Insert the depth stop (8) into the mounting hole as shown.

u Set the depth stop to the desired position. The maximum

drilling depth is equal to the distance between the tip of

the drill bit and the front end of the depth stop.

u Tighten the side handle by turning the grip clockwise.

Fittinganaccessory(g.B)

u Clean and grease the shank (9) of the accessory.

u Pull back the sleeve (10) and insert the shank into the tool

holder (6).

u Push the accessory down and turn it slightly until it fits into

the slots.

u Pull on the accessory to check if it is properly locked.

The hammering function requires the accessory to be able

to move axially several centimetres when locked in the

tool holder.

u To remove the accessory, pull back the sleeve (10) and

pull out the accessory.

KD985/KD990-Fittingthekeyedchuck(g.C)

u Fit the shank (11) of the supplied chuck (12) into the tool

holder as described above.

Warning! Never use keyed chucks in the hammer drilling mode.

KD985/KD990 - Fitting accessories in the keyed

chuck(g.D)

u Open the chuck by turning the sleeve (13).

u Insert the bit shaft (14) into the chuck.

u Insert the chuck key (15) into each hole (16) in the side of

the chuck and turn until tight.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving

parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When

using any tool for prolonged periods ensure you take

regular breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF.)

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Selectingtheoperatingmode(g.E)

The tool can be used in three operating modes. Rotate the

drilling mode selector (5) towards the required position, as

indicated by the symbols.

Drilling

u For drilling in steel, wood and plastics, and for screwdriving

set the operating mode selector (5) to the

position.

u When screwdriving, start at a low speed. When removing

screws, the speed is automatically reduced.

Hammer drilling

u For hammer drilling in masonry and concrete, set the

operating mode selector (5) to the

position

u When hammering, the tool should not bounce and run

smoothly. If necessary, increase the speed.

Hammering

u For hammering with spindle lock, and for light chiselling

and chipping, set the operating mode selector (5) to the

position.

u Make sure the forward/reverse switch is in the forward

position.

u When changing from hammer drilling to chiselling, turn the

chisel to the desired position. If resistance is felt during

mode change, slightly turn the chisel to engage the

spindle lock.

Selecting the direction of rotation

For drilling, for tightening screws and for chiselling, use forward

(clockwise) rotation. For loosening screws or removing a

jammed drill bit, use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(3) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

Warning! Never change the direction of rotation while the

motor is running.

Settingthedrillingdepth(g.F)

u Slacken the side handle (7) by turning the grip

counterclockwise.

u Set the depth stop (8) to the desired position. The

maximum drilling depth is equal to the distance between

the tip of the drill bit and the front end of the depth stop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KD976KA T3 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info