Bedienungsanleitung Black Decker KR1001 (Seite 5 von 78) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

602316

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

ENGLISH

(Original instructions)

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool:

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Variable speed control knob

4. Forward/reverse switch

5. Drilling mode selector

6. Chuck

7. Depth stop

8. Side handle

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle and depth stop (g. A)

u Turn the grip counterclockwise until you can slide the side

handle (8) onto the front of the tool.

u Rotate the side handle into the desired position.

u Insert the depth stop (7) into the mounting hole as shown.

u Set the drilling depth as described below.

u Tighten the side handle by turning the grip clockwise.

Setting the drilling depth (g. A)

u Slacken the side handle (8) by turning the grip counter-

clockwise.

u Set the depth stop (7) to the desired position. The maxi-

mum drilling depth is equal to the distance between the tip

of the drill bit and the front end of the depth stop.

u Tighten the side handle by turning the grip clockwise.

Fitting an accessory (g. B & C)

Keyless chuck with spindle lock (Where supplied) (g. B)

u Open the chuck by turning the sleeve (9) counterclock-

wise.

u Insert the bit shaft (10) into the chuck.

u Tighten the chuck by turning the sleeve clockwise.

Keyed chuck (Where supplied) (g. C)

u Open the chuck by turning the sleeve (11) counterclock-

wise.

u Insert the bit shaft (10) into the chuck.

u Insert the chuck key (12) into each hole (13) in the side of

the chuck and turn clockwise until tight.

Removing and retting the chuck (g. D)

u Open the chuck as far as possible.

u Remove the chuck retaining screw, located in the chuck,

by turning it clockwise using a screwdriver.

u Tighten an Allen key into the chuck and strike it with a

hammer as shown.

u Remove the Allen key.

u Remove the chuck by turning it counterclockwise.

u To ret the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Let the tool work at its own pace. Do not overload.

Warning! Before drilling into walls, oors or ceilings, check for

the location of wiring and pipes.

Selecting the drilling mode

u For hammer drilling in masonry and concrete, set the

operating mode selector (5) to the

position

u For drilling in steel, wood and plastics, set the operating

mode selector (5) to the

position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR1001 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info