Bedienungsanleitung Black Decker KR70LSR (Seite 4 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

461869

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional safety instructions for impact drills

◆ Wear ear protectors with impact drills. Exposure to

noise can cause hearing loss.

◆ Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

◆ This appliance is not intended for use by young or infirm

persons without supervision. Children must be supervised

to ensure they do not play with the appliance.

◆ If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse slider

4. Drilling mode selector

5. Side handle

6. Chuck

7. Bit storage

8. Latch

9. Laser unit

10. Wall mount

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting the side handle (fig. A)

◆ Screw the side handle (5) into the one of the holes (11) on

either side of the tool.

Fitting a drill bit or screwdriver bit (fig. B)

◆ Open the chuck by turning the front part (13) with one

hand while holding the rear part (12) with the other.

◆ Insert the bit shaft (14) into the chuck and firmly tighten

the chuck.

Removing and refitting the chuck (fig. C)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw, located in the front part

of the chuck, by turning it clockwise using a screwdriver.

◆ Tighten an Allen key (15) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Removing and replacing the laser unit

The tool provides a mounting location where the laser unit (9)

is stored when not in use.

◆ To remove the unit, release the latch (8) by pressing it

downward and slide the unit out of the mounting location.

◆ To replace the unit, release the latch (8) and slide the unit

into the mounting location.

Removing and replacing the wall mount

◆ To remove the wall mount (10), rotate the collar counter-

clockwise until the wall mount comes off the tool.

◆ To replace the wall mount (10), place the wall mount with

the legs closed in the hole in the bottom of the tool and

rotate the collar clockwise until the wall mount engages.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

◆ To select forward rotation, push the forward/reverse

slider (3) to the left.

◆ To select reverse rotation, push the forward/reverse slider

to the right.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

◆ For drilling in masonry, set the drilling mode selector (4) to

the

position.

◆ For drilling in other materials and for screwdriving, set the

drilling mode selector (4) to the

position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker KR70LSR Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info