Bedienungsanleitung Black Decker LZR210 T1 (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

578015

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

- Very humid conditions

- Shielded cables

◆ Before use, always test the tool by detecting a known

pipe or wire.

◆ If in doubt contact a qualified contractor.

Warning! This tool will not detect wires in circuits isolated

from the mains supply, cables operating at direct current (DC)

or wires used for telecommunication or computer systems.

Hidden wires (e.g. wall lights) may not be detected when

switches are in the off position.

Warning! This tool will not detect pipes of any other material

than metal.

Features

1. On/off switch (laser)

2. On/off switch (stud/metal finder)

3. Mode selector switch

4. LED indicators (stud/metal finder)

5. LED indicator (wire detector)

6. Insert holder

7. Marking/hanging insert

8. Keyhole insert

9. Spacer insert

10. Drywall pin

11. Laser apertures

Assembly

Fitting the battery (fig. A)

◆ Depress the release button and remove the battery cover

(12) from the tool.

◆ Connect the battery to the connector. The larger battery

terminal connects to the smaller connector terminal.

◆ Refit the cover and let it click into place.

Fitting and removing inserts

The marking/hanging insert (7) is used to make a mark on the

level line or to hang the tool on a drywall board using the

drywall pin (10) supplied. The keyhole insert (8) is used to

hang the tool on other types of wall using a screw or nail.

The spacer insert (9) is used to extend the laser line.

Fitting

◆ Place the insert into the holder from the back of the tool.

◆ Align the notches on the insert with the recesses in the

insert holder (6).

◆ Let the insert click into place.

Removing

◆ Keep the notches on the insert depressed.

◆ Push the insert out of the holder.

Use

Using the laser level function (fig. B)

◆ Place the tool flat against the wall as shown.

◆ Push the on/off switch (1) up to switch the tool on.

◆ Move the tool as necessary to position the laser lines.

◆ If necessary, hang the unit on the wall using the

appropriate insert.

Note: the laser lines will only be level if the tool is kept within

5° from vertical.

◆ Push the on/off switch (1) down to switch the tool off.

Using the spacer insert (fig. C)

If you need to extend the laser line, use the spacer insert (9)

as shown.

Note: the stud sensor cannot be used with the spacer insert

fitted.

Enhancing the visibility of the beam (fig. D)

If because of the lighting conditions it is difficult to see the

laser line, you can use one of the inserts as shown to enhance

the line.

Selecting the operating mode

◆ Set the mode selector switch (3) to the ‘STUD’ position for

the detection of wooden studs.

◆ Set the mode selector switch (3) to the ‘METAL’ position

for the detection of metal studs, pipes, etc.

Using the stud finder function (fig. E)

You can use this function to find wooden and metal studs

through drywall boards up to 18 mm thick.

◆ Fit the marking insert (7).

◆ Set the mode selector switch (3) to the required position.

◆ Place the tool flat against the wall as shown.

◆ Keep the on/off switch (2) depressed.

The red LED indicator (4) will light up and the buzzer will

sound once while the tool is calibrating. After calibration is

completed:

◆ Slowly slide the tool in a horizontal direction. Make sure

not to tilt or lift the tool.

◆ When the red LED indicator (4) lights up, slow down and

slide the tool further until the buzzer sounds and the top

green LED indicator is on.

This position indicates the one edge of the stud.

◆ Mark this position through the hole in the marking insert

(7).

◆ Move the unit further until the LED indicators are off.

◆ While still keeping the on/off switch (2) depressed, move

the tool in the opposite direction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker LZR210 T1 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker LZR210 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info