Bedienungsanleitung Black Decker MT1435 (Seite 7 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

529661

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

(Original instructions)

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Selecting the torque or drill position (g. D)

This tool is tted with a collar to set the torque for tightening

screws.

u For drilling, set the collar (8) to the drilling position by

aligning the symbol with the marking (12).

u For screwdriving, set the collar to the desired setting.

u If you do not yet know the appropriate setting, proceed as

follows:

t Set the collar (8) to position 1.

t Tighten the rst screw.

t If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting.

Selecting the direction of rotation (g. E)

For drilling and tightening screws,

use forward (clockwise) rotation. For loosening screws or

removing a jammed drill bit, use reverse (counterclockwise)

rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/re-

verse slider (2).

u To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

u To switch the tool off, release the variable speed switch.

Hints for optimum use

Drilling

u Always apply a light pressure in a straight line with the drill

bit.

u Just before the drill tip breaks through the other side of the

workpiece, decrease pressure on the tool.

u Use a block of wood to back up workpieces that may

splinter.

u Use spade bits when drilling large diameter holes in wood.

u Use HSS drill bits when drilling in metal.

u Use masonry bits when drilling in soft masonry.

u Use a lubricant when drilling metals other than cast iron

and brass.

u Make an indentation using a centre punch at the centre of

the hole to be drilled in order to improve accuracy.

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight line

with the screw.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to

high quality standards and designed to enhance the perform-

ance of your tool. By using these accessories you will get the

very best from your tool.

Maintenance

Your Black & Decker corded/cordless appliance/tool has been

designed to operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation depends

upon proper tool care and regular cleaning.

Warning! Before performing any maintenance on corded/

cordless power tools:

u Switch off and unplug the appliance/tool.

u Or switch off and remove the battery from the appliance/

tool if the appliance/tool has a separate battery pack.

u Or run the battery down completely if it is integral and then

switch off.

u Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.

u Regularly clean the ventilation slots in your appliance/tool/

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior (when tted).

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker MT1435 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info